Panasonic AJ-SD755 Rear panel, 6Remote control connectors, In/Out, AC IN socket

Parts and their functions

Rear panel

1 2 3 45 6 7 8 9: ;

6Remote control connectors

These connectors make it possible to use two of

AC IN

SIGNAL

GND

AES/EBU

CH1/2

IN

CH1/2

OUT

Y

PB

PR

ANALOG

VIDEO

IN

ON

Y75Ω

	OFF
PB	REF VIDEO
	IN
	ON
PR	75Ω
	OFF

1VIDEO OUT

2

(WFM)

3

(SUPER)

REMOTE

REMOTE IN/OUT

REMOTE OUT

ENCODER REMOTE

RS-232C

PARALLEL

	ANALOG
CH1 PUSH AUDIO PUSH CH2			PUSH	TC
	IN			IN
				TC
				OUT
CH1	AUDIO	CH2		MON
	OUT			L
				MON
				R

	OPTION 1
	SDI
IN	OUT
	1

ACTIVE

THROUGH

2

	3
	(SUPER)
	OPTION 2
	SDTI
IN	OUT

1

2

these VTRs or to connect this VTR to an external

controller so that the VTR can be operated from an

external component.

Two remote control connectors are provided: one

for IN/OUT use and the other for OUT use only.

IN/OUT:

For connection with an external controller

SERVICE ONLY

1AC IN socket

Connect one end of the power cord supplied to this socket and the other end to the power outlet.

2DIGITAL AUDIO IN and OUT connectors

These are the input and output connectors for digital audio signals that comply with the AES/EBU standards.

<Note>

The digital audio signals which are to be input to these connectors must be synchronized with the video input signals. Otherwise, noise will be generated in the audio output signals.

3ANALOG COMPONENT VIDEO IN connectors The analog component video signals are input to these connectors.

4ANALOG COMPOSITE VIDEO IN connectors and 75 Ω termination switch

The analog composite video signals are input to these connectors. A loop-through configuration is featured for each pair of input connectors.

For termination at this VTR, set the termination switch to ON.

5REF VIDEO IN connectors and 75 Ω termination switch

These are the input connectors of the reference video signals.

Input a reference signal with color burst.

For termination at this VTR, set the termination switch to ON.

<Note>

Video and audio output may be disturbed when the reference video signal is not input, so it is recommended that a system which inputs the reference video signal be used.

For connection with deck-to-deck operations

OUT:

For connection with parallel run operations

For loop-through use

<Note>

If connection is to be made to the OUT connector

for deck-to-deck operations where this VTR will

serve as the recorder, which of the two connectors

is to be used can be selected using setup menu No.

212 (MASTER PORT).

7ENCODER REMOTE connector

An external encoder remote controller is connected to this connector when the video output signal settings are to be adjusted from an external component.

8ANALOG AUDIO IN connectors

These are the analog audio input connectors.

9TIME CODE IN connector

This connector is used to record an external time code onto the tape.

:TIME CODE OUT connector

During playback, the playback time code is output through this connector.

During recording, the time code generated by the internal time code generator is output.

;SDI input and output connectors (optional)

At these connectors, it is possible to input and output digital component audio and video signals which comply with the SMPTE 259M-C standard by installing the SDI board (AJ-YA755G, available as an optional accessory) in the VTR.

Video signals containing superimposed information can be output through the SDI OUT 3 connector. Whether the superimposing is to be set ON or OFF is selected using the SUPER switch W on the front panel.

<Note>

The digital audio signals which are to be input to these connectors must be synchronized with the video input signals. Otherwise, noise will be generated in the audio output signals.

13