Panasonic AJ-SDC905p 7-2-2OPTION MODE

Chapter 7 Menu description tables

7-2-2 OPTION MODE

Item/	Variable			Remarks
Data storage	range
P.OFF GPS DATA	HOLD	For selecting whether or not to hold the UMID
	CLEAR	GPS position information while the power is
		off and record the information as the data still
		held as the previous value until another
		measurement can be taken after the power is
		next turned on.
		HOLD: The data is held and recorded.
		CLEAR: The data is cleared at the same time
			as the power is turned off, and all
			zeros (no information) are recorded
			from the time the power is turned on
C U F			until the measurement is next taken.
COMPONENT OUT	OFF	For setting the analog component signal
	BETACAM	output level.
	M2	OFF:
		Output stops during power save. (Note that
		this setting is forced ON if a camera
		adapter is connected and a tally signal is
		detected from pin 26. Otherwise it is OFF.)
		BETACAM:
		Output at the ß-CAM level.
		M2:
C U F		Output at the M II level.
1394 TYPE	DVCPRO	For setting the format of the signals to be
	DV	output from the DVCPRO connector.
		DVCPRO:
		The signals are output in the DVCPRO
		(25M) format.
		DV:
		The signals are output in the DV format.
		<Note>
			SDC905
		The signals are output in the DVCPRO50
		format if 16:9/50M or 4:3/50M is selected as
		the REC MODE menu item setting on the
C U F		<SYSTEM MODE> screen.
1394 AUDIO IN	CH1/CH2	For selecting the channel on which the
	CH3/CH4	reception data is to be recorded on the tape
		when receiving DV format data in the 4CH
		audio signal mode and recording the data on
		a DVCPRO (25M) tape.
		CH1/CH2:
		The reception data is recorded on CH1 and
		CH2.
		CH3/CH4:
		The reception data is recorded on CH3 and
C U F		CH4.
1394 SPEED	S100	For setting the transfer speed of the signals to
	S200	be output from the DVCPRO connector.
	S400	S100: 100 Mbps
		S200: 200 Mbps
C U F		S400: 400 Mbps

Item/	Variable	Remarks
Data storage	range
1394 IN CH	0	For setting the input channel for the signals to
	:	be supplied to the DVCPRO connector.
	63	0-63:
	AUTO	The channel is fixed at the specified
		number.
		AUTO:
		The channel corresponding to the setting of
C U F		the externally connected unit is selected.
1394 OUT CH	0	For setting the output channel for the signals
	:	to be output from the DVCPRO connector
	63	0-63:
	AUTO	The channel is fixed at the specified
		number.
		AUTO:
		The channel corresponding to the setting of
C U F		the externally connected unit is selected.
26PIN VIDEO	COMPONENT	For setting the video signals to be output from	7
SELECT	VIDEO OUT	pin #4 of the 26-pin connector when a 26-pin
		camera adapter is connected.
		COMPONENT:
		The component Y signal is output.
		VIDEO OUT:
		The same signal (composite signal) as the
C U F		VIDEO OUT connector signal is output.
26PIN CONTROL	OFF	For setting whether recording is to be
	BOTH	controlled by the unit or by both the unit and
		the external VTR which is connected to the
		26-pin camera adapter.
		OFF:
		Recording is performed by the unit only. (It
		is not performed using the external VTR.)
		BOTH:
		Recording is performed by both the unit
		and the external VTR. The tally lamp
		indicates the status of the tally signal of the
		26-pin connector. (The tally lamp setting
		can be established using REC TALLY in
C U F		the SYSTEM MODE.)
26PIN CTL	NORMAL	For setting the control signal of the VTR to be
DEFAULT	SPECIAL	output from pin #12 of the 26-pin connector
		when using a VTR connected to a 26-pin
		camera adapter.
		NORMAL:
		STOP “low,” START “high” (for AJ-D92)
		SPECIAL:
C U F		STOP “high,” START “low”

The underlining in the variable range column indicates the setting in the preset mode.

81