Panasonic DVD-F61 Troubleshooting guide, Power, Operation, Picture, Units\for\Australia\and\N.Z

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem:

In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail consumerproducts@panasonic.com, or web site (http://www.panasonic.com).

In Canada, contact Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, web site (www.panasonic.ca), or an authorized Servicentre closest to you.

In other areas, consult your dealer.

		Power		Page
		No power.	≥Insert the AC power supply cord securely into the household AC outlet.	5
		The unit is automatically switched	≥The unit automatically switches to standby after approximately 30 minutes in the stop mode. Turn the	–
		to the standby mode.	power back to ON.	13
			≥The SLEEP timer functioned.
		Operation
		No response when buttons	≥Some operations may be prohibited by the disc.	–
		pressed.	≥The unit may not be operating properly due to lightning, static electricity or some other external	–
			factor.
			Reset procedure:
			Press [POWER Í/I] to switch the unit to the standby mode and then back to ON.
			Alternatively, press [POWER Í/I] to switch the unit to the standby mode, disconnect the AC power
			supply cord, and then reconnect it.
		No operations can be performed	≥Check that the batteries are installed correctly.	7
		with the remote control.	≥The batteries are depleted: Replace them with new ones.	7
			≥Point the remote control at the remote control sensor and operate.	3
		Play doesn’t start (or stops	≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.	–
		immediately) when you press	≥This unit cannot play discs other than the ones listed in these operating instructions.	6
		[1] (PLAY).	≥You can only play DVD-Video if their region number is the same or includes the same region number as	6
			the unit or if the DVD-Video is marked “ALL”. Confirm the region number for the unit on the rear panel.	6
			≥The disc may be dirty and may require cleaning.
			≥Ensure that the disc is loaded with the label of the side to be played facing upwards.	8
			≥Check that the DVD-RAM has something recorded on it.	–
		Cannot play DVDs.	≥Sequential Mode is on. Press [SEQUENTIAL] to turn Sequential Mode off.	9
		Cannot select alternative	≥This function depends on software availability.	–
		languages.	≥Try selecting from the disc’s menu if one is available.	8
Reference		No menu play.	≥This function depends on software availability.	–
		No subtitles.	≥This function depends on software availability.	–
			≥Subtitles are cleared from the television. Turn on the subtitles.	12
			≥Subtitle position is wrong. Adjust the position.	12
		Soundtrack and/or subtitle	≥This function depends on software availability.	–
		language is not the one selected
		with the SETUP menus.
		Cannot change angle.	≥This function depends on software availability. Even if a disc has a number of angles recorded, these	–
			angles may be recorded for specific scenes only.
		You have forgotten your ratings	≥While stopped, press and hold [:/6] and [;] on the unit and then also press and hold [<] on	–
		password.	the unit until “Initialized” disappears from the television. Turn the unit off and on again.
		Reset all the settings to Factory	All settings will return to the default values.
		Preset.
		The drawer stops while opening.	≥There are more than 5 discs in the unit. Remove one or more discs and turn the unit off and on again.	–
		Picture
		Picture distorted.	≥Some distortion is normal during SEARCH.	–
		Menu not displayed correctly.	≥Restore the zoom ratio to a1.00.	13
			≥Set the subtitle position to 0.	12
			≥Set “4:3 Aspect” to “Normal”.	16
		No picture.	≥Check the connection.	4
			≥Make sure the television is on.	–
			≥Ensure the television’s video input setting (e.g., VIDEO 1) is correct.	–
		The picture shown on the	≥Go to Video in the SETUP menus, and change “TV Aspect” to suit your television.	7, 18
		television is not normal.	≥Use the television to change the aspect to the correct one.	–
		(The sides of the picture are cut	If your television cannot change the aspect when input is progressive, try changing “4:3	16
		off, the picture is stretched	Aspect” with the on-screen menu icons.	13
		horizontally, or black bands	≥Turn off the zooming feature of your television if you are using Variable Zoom.
		appear at the top and bottom of	≥Ensure that the unit is connected directly to the television, and is not connected through a video	4
		the screen.)	cassette recorder.
		There is ghosting when	≥Change “Video output mode” to “480I”. This problem is caused by the editing method or material	17
		progressive output is on.	used on DVD-Video, but should be corrected if you use interlace output.
		Picture quality is poor.	≥Check the settings in the On-Screen Menu Icons’ Picture Menu.	17
		The SETUP menus and other	≥The unit and television are using different video systems.	–
		screens shown on the television	[Units\for\Australia\and\N.Z.]
		are displayed incorrectly.	Use a multi-system or PAL television.
		Colors appear faded.	[Units\for\Asia]
			Use a multi-system or NTSC television.
	RQT6726

20