Paging/Intercom, Intercom between Handsets | Panasonic KX-TCD700AL

700al australian 2 5 02 2/5/02 3:00 pm Page 25

Paging/Intercom➡

Paging All Handsets from the Base Unit

1.Z Ï (On the Base Unit).

• All handsets will ring for one minute.

2.To stop paging, Z Ï again or Z O on one of the handsets.

Intercom between Handsets

A 2-way intercom is available between handsets. Eg. Handset 1 is paging Handset 2

1.(Handset 1) Z N

(Int icon blinks until connection is established).

2.(Handset 1) Z B

3.(Handset 2)

When the unit rings, Z O to answer.

•The intercom duration is displayed.

4.(Handsets 1 and 2)

To end the intercom, Z P.

•Intercom calls can be conducted within the radio area of the current base unit, but not within units in neighbouring radio areas.

Intercom is not be acceptable in the following areas:

–when the other party is in intercom mode.

–when the other party is on hold during external call.

–while the other party is in conference call.

-1-œœœœœœœ02

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

(1)

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

(1)-(2)

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

00-00-00

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

CHAPTER 2

Transferring a Call from One Handset to Another

The intercom can be used during a call, enabling you to transfer a call between handsets registered to the same base unit.

Transferring a Call using the Intercom

Eg. Handset 1 is transferring an external call to Handset 2.

1.(Handset 1)

During a call, Z N (Intercom icon turns on).

•The call is put on hold.

2.(Handset 1) Z desired handset no. eg. B

•You will hear an internal ring back tone until the other handset is answered.

(1)

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

(1)-(2)

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

25

Image 25

Panasonic KX-TCD700AL Paging/Intercom, Paging All Handsets from the Base Unit, Intercom between Handsets

Contents

Charge the batteries for approx hours before initial use Operating Instructions Dear purchaser Important Information AC Adaptor Telephone Line Cord/Plug Batteries AA size Contents Programmable Functions Useful Information On the Base Unit Connections Getting Started Battery Charge Installing the Batteries in the HandsetBattery Strength Battery Information Battery Replacement Battery CautionRemember to charge the new batteries after replacement see Getting Started Safety Safety InstructionsInstallations Environment Placement Installation Safety InstructionsImportant Information for Australia only Wall Mounting Location of Controls Cancel ButtonBase Unit Handset Handset Display Symbols UsedIcons Shows that you should press the following keys Basic Start-up Operations To Dial After Confirming the Entered Number Making CallsTo Redial the Last Number Dialled To Redial After Confirming the Numbers in Redial Memory Making Calls To Select the Receiver VolumeTo Edit/Clear Numbers in the Redial List Direct Call Answering Calls Answering CallsAuto Talk To Turn the Handset Ringer Off Temporarily Storing Phone Numbers in Memory Speed DiallingDialling a Stored Number Y or Speed Dial Menu Saving Numbers in Speed Dial List save speed Speed DiallingDisplay number to be saved How Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Caller ID Sub-Menu Caller ID Service When Viewing Long Telephone Numbers Using the Caller ListViewing the Caller List What ‘⁄’ means For Optional Multi-Unit Users Using the Caller ListCalling Back from the Caller List Operating More than One Handset Paging/Intercom Transferring a Call using the IntercomPaging All Handsets from the Base Unit Intercom between Handsets Paging/Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerTransferring a Call without the Intercom Conference How to Use the Pause Feature Special FeaturesUsing the Recall Feature Using Caller ID Type Setting the Key Lock on Special FeaturesTo Cancel the Key Lock Y for more than 2 seconds On the Handset Summary of Programmable Functions To Stop the Alarm Setting Time Alarm FunctionSet Time of Alarm set time Time alarm Set Range Warning Alarm ON/OFF range alarm on/off Setting Tone OptionsSet Battery Low Tone ON/OFF battery low on/off Set Key Confirmation Tone ON/OFF key tone on/off Select the Standby Mode Display standby mode Setting Display OptionsSelect the Talk Mode Display talk mode Setting Direct Call ON/OFF set direct on/off see Setting Call OptionsSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Select Battery Type battery type Setting Other OptionsSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Register a Handset to a Base Unit register hs RegistrationHold Ï on base unit for 10 secs Cancelling a Base Unit cancel base Specified Base Unit Access eg. base Automatic Base Unit Access autoSelect Base Unit select bs Function Initial Setting Reset Handset reset hs Bell Selection Programmable Functions On the Base UnitOr U Select all handsets to ring Select Pause Timing Select Flash ModeSelect Flash Timing Select Pause Timing Cancelling a Handset Cancelling a HandsetProgrammable Functions On the Base Unit Set the Base Unit PIN Call Restriction When you dial a restrictedRestricted Numbers Setting the Clock To Select the Base Unit Ringer VolumeSelect Ringer Volume Setting the Clock Function Initial Setting Reset Base Unit Option Covers Using the Belt Clip Before Requesting Help Problem Remedy Call is being received. To answer, Z P then Before Requesting Help Adding Another PhoneTelephone Double Adaptor Panasonic Technics 700al australian 2 5 02 2/5/02 300 pm 700al australian 2 5 02 2/5/02 300 pm N52