Programming

3

Enter the desired hour and minute you

 

 

 

 

 

 

 

 

Incoming call barring (Caller ID

 

wish to start this feature. a

 

 

 

 

 

 

subscribers only)

 

 

 

R You can select 24-hour or 12-hour

 

 

 

 

 

clock format (AMor PM) by

 

 

 

This feature allows the unit to reject calls from

 

pressing

.

 

 

 

specified phone numbers that you do not want

4

Enter the desired hour and minute you

 

 

to answer such as junk calls.

 

 

 

 

When a call is received, the unit does not ring

5

wish to end this feature. a

 

 

 

while the caller is being identified. If the phone

M

N

 

 

 

 

number matches an entry in the call barred

 

R When the night mode is set,

is

 

 

list, the unit sends out a busy tone to the

 

 

 

caller, and then disconnects the call.

 

 

displayed.

 

 

 

 

 

 

 

 

 

 

Important:

 

 

 

 

 

 

 

 

 

 

 

 

 

Changing the start and end time

 

 

 

R When the unit receives a call from a

 

1

 

#237

 

 

 

 

number that is stored in the call barred list,

 

 

 

 

 

the call is logged in the caller list

 

2

Continue from step 3, “Turning night

 

 

(page 31) with after the call is

 

 

mode on/off”, page 26.

 

 

 

disconnected.

 

 

 

 

 

 

 

 

Setting the ring delay

 

 

 

 

 

 

 

 

Storing unwanted callers

 

This setting allows the handset to ring during

 

 

You can store up to 30 phone numbers in the

night mode if the caller waits long enough.

 

 

 

 

call barred list.

 

 

 

After the selected amount of time passes, the

 

 

 

 

 

 

 

Important:

 

 

 

handset rings. If you select No Ringing,

 

 

 

 

 

 

 

R You must store the phone number with an

the handset never rings during night mode.

 

 

1

 

#239

 

 

 

 

area code in the call barred list.

 

 

 

 

 

 

n From the caller list:

 

 

2

MbN: Select the desired setting. a

 

 

 

 

 

 

 

1

MFN (

)

 

 

 

a M

N

 

 

 

 

 

 

 

 

 

 

2 MbN: Select the entry to be barred. a

 

 

 

 

 

 

 

Changing the handset name

 

 

3

MbN: Caller Barreda

 

Each handset can be given a customised

 

 

 

4

MbN: Yesa

a M

N

name (“Bob”, “Kitchen”, etc.). This is useful

 

when you make intercom calls between

 

 

 

n By entering phone numbers:

 

handsets. You can also select whether or not

 

1

#217 a

 

 

the handset name is displayed in standby

 

 

2 Enter the phone number (24 digits

mode. The default setting is No. If you select

 

 

Yeswithout entering any handset name,

 

 

 

max.). a

 

 

Handset 1to Handset 6is displayed.

 

3

R To erase a digit, press

.

1

 

#104

 

 

 

M

N

 

 

2

Enter the desired name (max. 10

 

 

 

 

 

 

 

 

 

 

 

Viewing/editing/erasing bar call

 

 

characters; page 38).

 

 

 

 

3

R If not required, go to step 3.

 

 

 

numbers

 

 

 

 

 

 

 

 

1

#217

 

 

4

MbN: Select the desired setting. a

2

 

 

 

 

 

2 MbN: Select the desired entry.

 

 

times

 

 

 

 

 

5

 

 

 

 

R To exit, press M

N.

 

M

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

27

TG6711FX(en)_0130_ver002.pdf 27

2012/01/30 18:56:54

Page 27
Image 27
Panasonic KX-TG6711FX Incoming call barring Caller ID, Subscribers only, Changing the handset name, Numbers