Panasonic KX-TG8231, KX-TG8232 - page 43

Useful Information

For assistance, please visit http://www.panasonic.com/help 43

Battery recharge

I cannot program items. LProgramming is not possible while either the

base unit or another handset is being used. Try

again later.

While programming, the

handset starts to ring.

LA call is being received. Answer the call and

start again after hanging up.

I cannot register a handset

to a base unit.

LThe maximum number of handsets (6) is already

registered to the base unit. Cancel unused

handset registrations from the base unit (page

38).

LPlace the handset and the base unit away from

other electrical appliances.

Problem Cause/solution

The batteries should be

charging but the battery

icon does not change.

LClean the charge contacts and charge again

(page 13).

The handset beeps

intermittently and/or )

flashes.

LFully charge the batteries (page 13).

I fully charged the

batteries, but ) still

flashes.

LClean the charge contacts and charge again

(page 13).

LIt is time to replace the batteries (page 12).

I fully charged the

batteries, but the operating

time seems to be short.

LWipe the battery ends (S, T) and the unit

contacts with a dry cloth.

The handset display is

blank.

LThe handset is in screen saver mode (page 14).

Press {OFF} to activate the handset display

again.

LConfirm that the batteries are properly installed.

LFully charge the batteries (page 13).

Problem Cause/solution

TG8231_8232.book Page 43 Thursday, July 19, 2007 3:22 PM

Contents

Main Table of Contents Introduction Preparation Making/Answering Calls Phonebook Caller ID Service Product information KX-TG8231 KX-TG8232 Accessory information Supplied accessories Page Important safety instructions WARNING CAUTION For best performance Page Controls Base unit Handset Displays Volume up Volume down j M K Connections Base unit C Charger (KX-TG8232) I Hooks (120 V AC, 60 Hz) To single-line telephone jack (RJ11C) A B B Battery installation and replacement 1 ack (RJ11C) Rechargeable Ni-MH ONLY 2 Noise filter Battery charge Screen saver mode Symbols used in these operating instructions Setting up the unit before use Display language 1 2 Page Making calls Answering calls Making/Answering Calls 2 Useful features during a call MUTE button FLASH button For Call Waiting service users Temporary tone dialing (for rotary/pulse service users) Page Phonebook Handset phonebook 7 6 Adding entries 1 2 3 4 Page Phonebook 3 4 5 One touch dial 1 Copying handset phonebook entries Caller ID Service Using Caller ID service Group settings for handset phonebook 1 2 3 Caller list Page Programmable settings Programming by scrolling through the display menus 1 2 3 4 *Ringer settings Ringer volume 28 *Other settings Key tone + Alarm 1 2 3 Page Answering system Memory capacity Turning the answering system on/off Using the base unit Using the handset 1 Listening to messages using the base unit Listening to messages using the handset 1 2 3 1 2 Remote operation Using the answering system remotely 1 2 3 4 Answering system settings Remote access code 1 3 4 Ring count 1 3 4 Callers recording time Using Voice Mail service Operating additional handsets Intercom Transferring calls between handsets, conference calls Multi-unit Operation 1 Registering a handset to a base unit 1 2 3 4 Page Belt clip Headset (optional) Error messages Troubleshooting 1 2 Page Page Page Page Page FCC and other information CAUTION: NOTE: E NERGY S Specifications Page Warranty Panasonic Telephone Products Limited Warranty Limited Warranty Coverage Mail-In Service Limited Warranty Limits And Exclusions Index Index If you need assistance with setup or operation 1 2 3 When you ship the product PQQX16247ZB