Setting the Remote Control to Operate Your TV

You can operate the TVs of the manufacturers listed below with the remote control after setting it.

This setting procedure allows you to operate the TVs of some manufacturers using the supplied remote control.

Preparation

• Set [VCR/TV] switch (22) to [TV].

Operations

1Find the manufacturer number of your TV while referring to the following table.

2While holding down [TV-ON/OFF] (1) on the remote control, use [Numeric] (2) to enter the manufacturer number. This completes the settings for the TV manufacturer.

Be sure to enter the number in two digits. Example: 1 ) 01

3To confirm the correct settings were made, check whether the TV can be operated properly.

When a manufacturer has multipled numbers in the following table, try entering other numbers if the TV operations cannot be performed properly, and then select the optimal number.

Notes:

If you are using a Panasonic TV, this setting has already been made, and so you do not need to perform the above setting procedure. However, this remote control may not work with some Panasonic TVs.

Some TV models cannot be operated using this remote control (including all TVs non-remote compatible).

List of TVs Compatible with the VCR Remote Control

[Brand]

[Code]

 

 

Panasonic/National

01-04

 

 

SONY

05

 

 

TOSHIBA

06

 

 

JVC

07

 

 

HITACHI

08

 

 

MITSUBISHI

09, 10

 

 

SHARP

11

 

 

PHILIPS, SAMSUNG

12

 

 

NEC

13

 

 

SANYO

14

 

 

GOLDSTAR/LG

15, 16

 

 

SAMSUNG

17,18

 

 

SANYO

19

 

 

Connections

This section shows you how to connect the VCR to an aerial, TV, etc.

Basic Connections

The following connections are required to record and play back the video cassette through the TV.

 

 

(1)

 

(3)

(2)

 

 

(4)

 

AC IN ~

2 IN

 

 

(6)

VIDEO2

 

AUDIO2

2 OUT

 

IN (AV1) OUT

RF

 

 

(5)

 

¢

 

(1) Aerial (Not supplied)

(6) AC Input socket (48)

(2) TV Set (Not supplied)

¢ To mains supply

(3)Aerial Connector

(4)RF IN socket (51)

(5)RF OUT socket (52)

Connection to a TV using the Audio/Video Input Socket:

Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable. (See page 6.)

 

 

 

 

(1)

 

 

(3)

(2)

 

 

 

(4)

(5)

 

 

 

 

(6)

(7)

 

 

 

 

 

AC IN ~

 

2 IN

 

 

 

 

 

 

(10)

VIDEO2

 

 

 

AUDIO2

2 OUT

 

 

 

IN (AV1) OUT

RF

 

 

 

(9)

 

(8)

 

 

 

 

 

¢

 

 

 

(1)

Aerial (Not supplied)

 

(8) RF OUT socket (52)

 

(2)

TV Set (Not supplied)

 

(9) VIDEO OUT (50)/

 

(3)

Aerial Connector

 

AUDIO OUT (53)

 

(4)

VIDEO IN

 

(10)AC Input socket (48)

 

(5)

AUDIO IN

 

¢ To mains supply

 

(6)Audio Cable/Video Cable (Not supplied)

(7)RF IN socket (51)

5

Page 5
Image 5
Panasonic NV-MV40GL specifications Setting the Remote Control to Operate Your TV, Basic Connections, Preparation