Remote control operation

Adjusting the waveform of the input signal

You can monitor if the brightness and contrast level of the input signal is in the recommended range by displaying it in the waveform monitor. See "WAVEFORM MONITOR" on page 32.

1.Project a commercial adjusting signal.

2.Press the WAVEFORM button to display the waveform monitor.

Adjusting the waveform

Make sure to adjust to the 0% line first. Any signal level below the recommended range will be forced to 0%.

Adjusting in PICTURE menu

Press PIC. ADJUST button to display the PICTURE menu and adjust BRIGHTNESS (-32 to +32) and CONTRAST (-64 to +64) with I H.

Basic Operation

OFF

Deactivate the waveform monitor.

 

 

 

Monitoring the waveform of

FULL SCAN

brightness and contrast of the

 

whole image.

 

Monitoring the waveform of

SINGLE LINE

detailed brightness and contrast in

each horizontal line of the image.

SCAN

Press F G to select the required

 

 

line.

3.Press ENTER button to select the required adjusting mode.

BRIGHTNESS

Adjust the bottom line of the

waveform to 0 % (0/7.5 IRE).

 

CONTRAST

Adjust the top line of the waveform

to 100 % (100 IRE).

 

Adjusting in ADVANCED menu

Press PIC. ADJUST twice to display the ADVANCED menu and adjust BRIGHTNESS (-16 to +16) and CONTRAST (-32 to +32) in red, green and blue with I H.

In red

FULL SCAN(Y)

FULL SCAN(R)

FULL SCAN(G)

FULL SCAN(B)

SINGLE LINE SCAN(B)

SINGLE LINE SCAN(G)

SINGLE LINE SCAN(R)

SINGLE LINE SCAN(Y)

 

waveform to 0 % (0/7.5 IRE).

CONTRAST R

Adjust the top line of the waveform

to 100 % (100 IRE).

 

In green

 

 

 

BRIGHTNESS G

Adjust the bottom line of the

waveform to 0 % (0/7.5 IRE).

CONTRAST G

Adjust the top line of the waveform

to 100 % (100 IRE).

 

4.Press F G I H to adjust the displaying position of the waveform monitor.

5.Adjust the waveform in each menu.

NOTE:

When you adjust the SINGLE LINE SCAN, the position of the waveform is depends on the position of the selected line.

When the WAVEFORM displayed, the COLOR MANAGEMENT is disabled.

In blue

 

 

 

BRIGHTNESS B

Adjust the bottom line of the

waveform to 0 % (0/7.5 IRE).

CONTRAST B

Adjust the top line of the waveform

to 100 % (100 IRE).

 

NOTE:

When the Main menu (except WAVEFORM and individually displayed menu item) is displayed, the waveform monitor will be halt.

When the waveform monitor is displayed, the Main menu will be displayed in order not to interfere the waveform monitor.

100%

50%

0%

ENTER

Signal level

Adjust to 100%

100%

50%

Optimal dynamic range

0%

Monitor position Adjust to 0%

 

PC/HDMI (Expand)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjust to 100%

level

100%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal

 

 

50%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

dynamic range

 

 

 

0%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Optimal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Monitor position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjust to 0%

 

 

 

 

 

 

 

 

 

 

 

 

 

24 - ENGLISH

Page 24
Image 24
Panasonic PT-AE1000U Adjusting the waveform of the input signal, Adjusting in Picture menu, Adjusting in Advanced menu