Appendices
|
| Scanning |
|
|
| 3 | |
| Display | frequency | Dot clock |
| Plug and play * | ||
Mode | resolution *1 |
|
| frequency | Format | COMPUTER 1/ |
|
| (dots) | H (kHz) | V (Hz) | (MHz) |
| HDMI | |
|
|
|
|
|
| COMPUTER 2 |
|
|
| 63.98 | 60.0 | 108.00 | R/H | - | - |
SXGA | 1 280 x 1 024 | 76.97 | 72.0 | 133.00 | R/H | - | - |
|
| 79.98 | 75.0 | 135.00 | R/H | o | o |
1366x768 | 1 366 x 768 | 47.72 | 59.8 | 84.75 | R/H | - | - |
SXGA+ | 1 400 x 1 050 | 65.32 | 60.0 | 121.75 | R/H | - | - |
WXGA+ | 1 440 x 900 | 55.94 | 59.9 | 106.50 | R/H | - | - |
UXGA | 1 600 x 1 200 | 75.00 | 60.0 | 162.00 | R/H | o | o |
WSXGA+ | 1 680 x 1 050 | 65.29 | 60.0 | 146.25 | R/H | o*4 | o*4 |
*1: “i” added to the resolution value indicates an interlaced signal.
*2: HDMI signal of 480i and 576i is only supported by 27MHz Dot clock signal.
*3: Where marked "o" signals indicates in Plug and Play is compatible with EDID of projector. Unmarked signals in Plug and Play may also be compliant if input terminals are written in the format list. Where Plug and Play is unmarked and nothing is written in the format list, difficulties in projecting image may occur even when computer and projector appear to have same resolution.
*4: For
3D compatible signals
3D compatible video signals of this projector are shown in the table below.
|
| Display | Frame | Top and | Frame | Field | |||
Mode | 3D signals | resolution *1 | |||||||
|
| (dots) | Packing | (Half) | Bottom | Sequential | Sequential | ||
|
|
|
|
|
|
| |||
| 750 (720)/60p | 1 280 x 720 | o | - | o | - | - | ||
|
|
|
|
|
|
|
| ||
| 750 (720)/50p | 1 280 x 720 | o | - | o | - | - | ||
| 1125 (1080)/60i | 1 920 x 1 080i | - | o | - | - | - | ||
HDMI | 1125 (1080)/50i | 1 920 x 1 080i | - | o | - | - | - | ||
1125 (1080)/24p | 1 920 x | 1 080 | o | - | o | - | - | ||
| |||||||||
|
|
|
|
|
|
|
|
| |
| VGA@120 Hz | 640 x | 480 | - | - | - | o | - | |
| SVGA@120 Hz | 800 x | 600 | - | - | - | o | - | |
| XGA@120 Hz | 1 024 x 768 | - | - | - | o | - | ||
COMPUTER 1/ | VGA@120 Hz | 640 x | 480 | - | - | - | o | - | |
|
|
|
|
|
|
|
| ||
SVGA@120 Hz | 800 x | 600 | - | - | - | o | - | ||
COMPUTER 2 | |||||||||
| XGA@120 Hz | 1 024 x 768 | - | - | - | o | - | ||
NTSC |
| - | - | - | o | o | |||
|
|
|
|
|
|
|
|
| |
Video and
Note
zzThe number of display dots is 1 280 x 800 for the |
|
A signal with a different resolution will be projected after converting the resolution to match the projector display. |
|
zzWhen interlaced signals are connected, flicker may occur on the projected image. |
|
zzEven the above signals exist, some image signals that recorded in special method may not be displayed. |
|
zzThe <AUTO ADJ.> operation may not optimize the image position or the resolution, depending on the input signal format or | Appendix |
the image contents. In this case, switch to a different image and execute <AUTO ADJ.> again. | |
|
ENGLISH - 69