Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 5400 manual Line Setup, Configuring PPPoE

Models: 5400

1 61

Download 61 pages 4.88 Kb

Page 37

SmartNode 5400 Getting Started Guide	5 • G.SHDSL Basic Configuration

Introduction

The SN5400 model has an option for a built-in G.SHDSL modem. The modem appears in the configuration as "port dsl 0 0" mode.

Profile

napt

WAN

port dsl 0\ 0\

	pvc
vpi 8	vci 35

pppoe

session MyISP

use
profile
WAN	napt

WAN

interface

bind subscriber
	MySubscriber
interface
bind	router
WAN

Subscriber PPP MySubscriber

CAUTION

context

ip

Figure 8. Configuring the G.SHDSL card for PPPoE

The Modem setup uses IP messages within its own subnet: 192.0.2.0/24. SmartNodes with built-in modems cannot use this subnet in any other way.

Note For information about the specifications of the G.SHDSL daughter card, see Appendix B, “Specifications” on page 46.

Line Setup

There is no line modulation setting. The modems automatically adapt to the bit rate and modulation used. The status LED on the back of the device is blinking while the modem attempts to connect and lit when the link is established. If the modem keeps blinking, check the cabling,

Configuring PPPoE

Figure 8 explains how to configure PPPoE on the SmartNode’s built-in G.SHDSL card. To configure the DSL port for PPPoE, first you need to log in to the SmartNode via the CLI and enter configuration mode.

login: administrator

password: <enter> SN4xxx>enable SN4xxx>#configure

Introduction

37

Image 37

Patton electronic 5400 manual Line Setup, Configuring PPPoE

Contents

SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations General conventions Typographical conventions used in this documentConvention Meaning General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Low-Voltage Directive SafetyCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Voice signalling Voice processing signalling dependentData connectivity Fax and modem supportManagement IP servicesSystem PhysicalFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination