Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 5400 Data connectivity, Voice processing signalling dependent, Voice signalling

Models: 5400

1 61

Download 61 pages 4.88 Kb

Page 47

SmartNode 5400 Getting Started Guide	B • Specifications

Data connectivity

Two 10/100/1000Base-Tx Gigabit Ethernet ports

All ports full duplex, autosensing, auto-MDX

Voice processing (signalling dependent)

Four or eight full-duplex channels with Voice CODECS:

•G.711 A-Law/ -Law (64 kbps)

•G.726 (ADPCM 16, 24, 32, 40 kbps)

•G.723.1 (5.3 or 6.3 kbps)

•G.729ab (8 kbps)

•Transparent ISDN data

G.168 echo cancellation (128 ms)

Up to 120 simultaneous voice or T.38 fax calls

DTMF detection and generation

Carrier tone detection and generation

Silence suppression and comfort noise

Adaptive and configurable dejitter buffer

Configurable tones (dial, ringing, busy)

Configurable transmit packet length

RTP/RTCP (RFC 1889)

Fax and modem support

Automatic fax and modem detection

Codec fallback for modem-bypass

T.38 Fax-Relay (Gr. 3 Fax, 9.6 k, 14.4 k)

G.711 Fax-Bypass

Voice signalling

SIPv2

H.323v4

MGCP/IUA

SIP call transfer, redirect

Overlap or en-bloc dialing

DTMF in-band, out-of-band

Data connectivity

47

Image 47

Patton electronic 5400 Data connectivity, Voice processing signalling dependent, Fax and modem support, Voice signalling

Contents

SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General observations Convention Meaning Typographical conventions used in this documentGeneral conventions General information Chapter contentsSN5400 model codes SmartNode 5400 overviewSmartNode 5400 rear panel ports are described in table SmartNode 5400 rear panelWAN ETH 0/0 SN5400 SmartNode 5400 front panelDescription LEDApplications overview Typical application IntroductionSmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Configuring the desired IP addressFactory-default IP settings LoginLAN Connecting the SmartNode to the networkLoading the configuration optional Step Command Purpose BootloaderStart Bootloader Start-up with factory configurationStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Command Purpose Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Using PVC channels with PPPoEDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceAppendix a Compliance information Authorized European Representative Low-Voltage Directive SafetyCompliance CE Declaration of ConformityAppendix B Specifications Fax and modem support Voice processing signalling dependentVoice signalling Data connectivityPhysical IP servicesManagement SystemFactor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Appendix D Port pin-outs Console port Pin SignalShdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination