SmartNode Model SysObjectID | Patton electronic 5400 manual

SmartNode 5400 Getting Started Guide	B • Specifications

Identification of the SmartNode devices via SNMP

All SmartNode devices have assigned sysObjectID (.iso.org.dod.internet.mgmt.mib-2.system.sysObjectID) numbers (see table 12).

Table 12. SmartNode Models and their Unique sysObjectID

SmartNode Model	SysObjectID

SN5400/32P/EUI	.iso.org.dod.internet.private.enterprises.patton.products.sn5400.1
	1.3.6.1.4.1.1768.100.4.13.3
SN5400/64P/EUI	.iso.org.dod.internet.private.enterprises.patton.products.sn5400.2
	1.3.6.1.4.1.1768.100.4.13.4

According to table 12, an SNMP get request to .iso.org.dod.internet.mgmt.mib-2.system.sysObjectID of a Smart- Node 5400/32P/EUI device reads out a numeric OID of 1.3.6.1.4.1.1768.100.4.10.1. The mapping of the sysObjectID to each of the SmartNode model is realized with the SmartNode product identification MIB.

The SNMP agent running in SmartWare is SNMP version 1 (SNMPv1) compliant. SNMP version 2 (SNMPv2) and SNMP version 3 (SNMPv3) are not currently supported.

IMPORTANT

Identification of the SmartNode devices via SNMP

50

Image 50

Patton electronic 5400 manual Identification of the SmartNode devices via Snmp, SmartNode Model SysObjectID

Contents

SmartNode 5400 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Precautions Impaired functioning Safety when working with electricity General observations Convention Meaning Typographical conventions used in this documentGeneral conventions Chapter contents General information SmartNode 5400 overview SN5400 model codes SmartNode 5400 rear panel SmartNode 5400 rear panel ports are described in table WAN ETH 0/0 SmartNode 5400 front panel SN5400 LED Description Applications overview Introduction Typical application SmartNode installation Site log Planning the installationNetwork Diagram Network information Installing the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Internal AC Power Supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PC Login Configuring the desired IP addressFactory-default IP settings Changing the WAN IP address Connecting the SmartNode to the network LAN Loading the configuration optional Start-up with factory configuration BootloaderStart Bootloader Step Command Purpose Step Command Purpose Load a new application image SmartWare via the serial link Xmodem ymodem -b Additional information Shdsl Basic Configuration Line Setup Configuring PPPoE Configuration Summary Using PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Command Purpose Troubleshooting DSL Connections Diagnostics Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbers Appendix a Compliance information CE Declaration of Conformity Low-Voltage Directive SafetyCompliance Authorized European Representative Appendix B Specifications Data connectivity Voice processing signalling dependentVoice signalling Fax and modem support System IP servicesManagement Physical Shdsl Daughter Card if applicable Factor Specs Identification of the SmartNode devices via Snmp SmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal Console Ethernet Appendix D Port pin-outs Pin Signal Console port Shdsl port Appendix E SmartNode 5400 factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses