Peavey GTX EQ in Switch, AUX Sends 1&2 and 3&4 Individual Level Controls, PRE/POST Switch

CENTURY SERIES GTX

EQ IN Switch

Inserts the EQ section into the input channel (post insert, pre fader). An associated green LED illuminates when the switch is down.

AUX SENDS 1&2 and 3&4 Individual Level Controls

Adjusts signal level sent to respective Aux buses. The signal source for these mixes may be selected pre or post fader by an associated switch. AUX pairs 1&2 and 3&4 are configured as dual concentric pots with the inner knobs controlling the odd sends (1&3), and the outer knobs controlling the even sends (2&4).

PRE/POST Switch

Switches the Aux 1&2 and Aux 3&4 signal sources between pre and post fader positions.AUX SENDS 5-8

Individual Level Controls

Adjusts signal level sent to respective Aux buses. The signal source for these mixes may be selected pre or post fader by the associated AUX 5&6 PRE/POST or AUX 7&8 PRE/POST switches.

Aux 8 Direct Switch

Removes the Aux 8 signal from the Aux 8 bus, and assigns the signal to the direct out 1/4" connector on the rear panel, instead of the normal post fader Dir Out signal.

AUX 5&6 PRE/POST Switch

Switches the Aux 5 & 6 signal sources between pre and post- fader.

AUX 7&8 PRE/POST Switch

Switches the Aux 7 & 8 signal sources between pre and post- fader

PAN CONTROL

Positions the channel image between left and right or between left-center-right. (See L-C-R Switch)

MUTE Switch with LED

Mutes the channel and all send functions. Mute does not affect the PFL switch or the Peak and Signal Present LED indicators. Red LED illuminates when the channel is muted.

MONO Bus Assign Switch

Assigns the input signal directly to the Center / Mono bus.

L-C-R Switch

Configures Left/Right and Center/Mono assignments for L-C-

Rpanning. To enable L-C-R panning, L-R and Mono assign switches must be down.

PAN Switch / Group Assign Switches (1-8)

With PAN switch down, the PAN control varies the level of the group assignments with odd numbered groups on the left and even numbered groups on the right. With PAN switch up, groups can be individually selected and are unaffected by the PAN control. Group assign switches route signals to the Group buses.

PFL Switch

Samples the channel’s signal (pre-fader) and allows for moni- toring within the master section of the console. This signal is not affected by the Mute switch. When depressed, the signal level can be seen on the Solo meters (which brighten in inten- sity), and can be heard via the mixer’s headphone or local monitor output. When this PFL switch is depressed, the associ- ated yellow LED illuminates.

5-Segment LED Array

The signal is monitored pre-fader. Signal Present LED (green) responds to levels as low as -30 dB and comes to full bright- ness at -8dB, varying in intensity according to level. -6dB LED (green), 0dB LED (green), and +8 dB (yellow) illuminate accordingly. The Peak (red) LED responds to overloads at three points in the module; pre-EQ, post-EQ, and post-fader.

100mm Fader

Used for control of all outputs of the channel except those Aux output sections selected by the PRE/POST switch to a pre- fader position. (The Insert output level is not affected by the fader position.)

Scene Mute Assignment Buttons

Assigns input channels to any of the four Scene Mute groups. Scene Mute combines with the module’s local Mute button, and actuates the local Mute LED.

Scene Mute Safe Switch

Disables any selected Scene Mute assignments. An associated green LED indicates the channel is in a Safe state.

PAGE 11