Pelco C1503M Preliminaries, Section, Programmingeliminaries And Configuration, CM9760-SAT, Figure

SECTION 2 PRELIMINARIES

PRELIMINARIES	2-1
1.0 SAT MENU PROGRAMMING	2-5
PROGRAM MODE
Camera Programming Menu	2-6
Monitor Programming Menu	2-8
Time-Date Programming Menu	2-11
Alarms Programming Menu	2-12
Ports Programming Menu	2-13
Auxiliaries Programming Menu	2-14
Password Programming Menu	2-14
Access Programming Menu	2-15

2.0	OTHER SAT PROGRAMMING	2-16
	OPERATIONAL MODE
	Presets	2-16
	Patterns	2-17
	Zones	2-18
3.0	9760 MGR-SAT PROGRAMMING	2-19
	PROGRAMMING MODE
	Comms File	2-19
	Cameras File	2-20
	Link Cameras File	2-20
	Alarm File	2-21

You can program the CM9760-SAT from the SAT SIDE, using a local	Interspersed with these programming setups is the need to integrate
keyboard and monitor, or you can program the SAT from the 9760	what is going to be programmed where, and by whom, given the various
SIDE, using a 9760-KBD and a system monitor assigned to that opera-	configurations of equipment possible. In the illustrations and explana-
tor. These two basic programming methodologies are not, however,	tions below, we discuss some of these variations and indicate advan-
mutually exclusive. By that, we mean, choosing to program from one	tages, disadvantages and/or tradeoffs, if they exist, of each. We also
location does not necessarily exclude programming from the other. In-	describe how to reach the main SAT programming menu from the given
termediate variations to programming on just one side or the other are	programming location.
possible.
	There are essentially three basic programming configurations. After we
	look at those, we discuss a program variation.
NOTE: The illustrations in this section represent the functional rela-	NOTE: In those instances where we discuss procedures or actions
tionships of the equipment mix needed to accommodate each pro-	yet to be covered in the manual, we either give a sufficiently adequate
gramming choice that is discussed in the associated text.	(but abbreviated) discussion, or refer you to the appropriate manual
	reference.

1.Programming Configuration I – Program the SAT from the SAT SIDE only.

This choice implies that at least one monitor-out line on the SAT SIDE is utilized as a local monitor and that you have a keyboard connected to the SAT for programming purposes (see Figure 2-1).

(a)Initialize the keyboard to your local monitor (see Section 2, 1.0 SAT MENU PROGRAMMING)

(b)Press the PGM key on the KBD200 or 300.*

(c)Enter the password (default 2899100) and press the ACK key. This activates the main SAT programming menu.

Advantages: Local control and alarm notification operations are accessible on the SAT SIDE of the configuration. The system user can call up link cameras. Local SAT alarms can be viewed locally and/or automatically reported to the system user. Associated SAT alarm camera displays can be placed on tie lines for viewing on system alarm monitors (this is the primary configuration that we use when discussing SAT configuration, operation and program- ming). It encompasses all the elements that the SAT is designed to use and avoids programming from the system side, which is less efficient.

Disadvantages: From a system user viewpoint, local SAT op- eration and programming means someone must be stationed at the satellite location to fully utilize its functions. If you are interested only in alarm notification back to the system, you have, at most, only three tie lines available, instead of four.

*Although the KBD300V can be used for programming, we don’t mention it here because (1) it can only be hooked up using the SAT keyboard remote port and (2) it requires a dedicated local monitor-out line for its LCD display. The KBD300V is discussed in APPENDICES II and III.

Figure 2-1

Programming Diagram One

PROGRAMMINGELIMINARIES AND CONFIGURATION CM9760-SAT 2-1