Rack Mounting

The NET5308T-EXP mounts into an industry-standard 19-inch (48 cm) equipment rack. The NET5308T-EXP occupies one rack unit (1.75 inches or 4.5 cm) of vertical rack space. The hardware necessary to mount the NET5308T-EXP into a rack is supplied with the unit.

NOTES:

•If you installed the NET5300B on a desktop, you can also place up to two NET5308T-EXP units on top of the NET5300B. (NET5308T-EXP units do not include rubber feet.)

•You can mount a NET5300B and up to two NET5308T-EXP units to a wall using the WM5300 wall mount. Refer to the WM5300 Wall Mount Kit Installation manual (C2663M) for more information.

The rack must meet the following requirements:

•19-inch (48 cm) EIA-310-D compliant (rear column required to mount the NET5300B in the same rack).

•Rack column depth: 24 to 30 inches (61 to 76 cm).

•Column-mounting hole provisions: 10-32 UNF-2B threaded holes or square window holes on front columns.

•Door systems are acceptable. Front doors must have at least 2 inches (5.1 cm) between the NET5308T-EXP front bezel and the inside of the door. Rear doors can only be used on rack columns that are more than 26 inches (66 cm) deep.

WARNINGS:

•Secure the front and rear screws to the support rails.

•Make sure the NET5308T-EXP is level.

•Slots and openings in the cabinet provide ventilation to prevent the unit from overheating. Do not block these openings. Never place the unit near or over a radiator or heat register. When placing the unit in a rack, be sure to provide proper ventilation. Allow at least one rack unit (1.75 inches or 4.44 cm) of spacing between units.

To install the NET5308T-EXP in a rack:

NOTE: Figure 3 identifies each piece of hardware for this procedure.

1.If chassis mounting brackets are not attached: Attach one chassis mounting bracket to each side of the NET5308T-EXP. Use three 6-32 x 0.25-inch Phillips flat head screws for each bracket.

 

(3) SCREWS

ATTACH

6-32 X 0.25-INCH

BRACKETS

PHILLIPS FLAT HEAD

Figure 6. Attaching Chassis Mounting Brackets

2.Attach one front-mount rail to one rear-mount rail. Make sure the rails are mounted back to back, as shown in Figure 7. Depending on the rack, use two or three 8-32 x 0.375-inch Phillips truss head screws for each rail set. Leave the screws loose until step 9.

12

C2655M-A (10/08)

Page 11 Page 13
Page 12
Image 12
Pelco NET5308T-EXP manual Rack Mounting, Brackets
Page 11 Page 13

NET5308T-EXP specifications

The Pelco NET5308T-EXP is an advanced network video encoder designed for high-performance video surveillance applications. This versatile device is notable for its ability to transform analog video feeds into digital signals, allowing for seamless integration with modern IP-based systems. This makes it an essential component for facilities looking to upgrade their security setups while retaining existing cameras.

One of the key features of the NET5308T-EXP is its capacity to handle up to eight analog video channels. This multi-channel capability allows users to manage multiple cameras through a single device, simplifying the installation and reducing the overall cost of upgrading surveillance systems. Each channel can process video in high-definition, ensuring that captured footage maintains clarity and detail, which is crucial for effective monitoring and incident investigation.

The NET5308T-EXP employs advanced H.264 video compression technology, which optimizes bandwidth usage without compromising video quality. This codec allows for the transmission of high-resolution video streams while minimizing data storage requirements. With the growing need for efficient data management in surveillance systems, this feature becomes invaluable, particularly in environments where bandwidth is limited.

Another significant aspect of the NET5308T-EXP is its support for Power over Ethernet (PoE). This technological integration enables the device to receive power and transmit data over a single Ethernet cable, greatly simplifying installation. It eliminates the need for multiple power sources and power adapters, allowing for cleaner setups and reducing cable clutter.

Moreover, the encoder includes advanced motion detection capabilities, which can trigger alerts based on movement within the camera’s field of view. These features can be essential for ensuring that security personnel are notified of potential security breaches in real time. Additionally, the device supports various networking protocols, enhancing its compatibility with a wide range of video management systems.

The NET5308T-EXP is designed for reliability and durability in various operating conditions. Its robust construction allows it to function in a range of environments, making it suitable for indoor and outdoor applications alike. With features such as video loss detection and alarm inputs, the device further assures its status as a top-tier solution for comprehensive security needs.

Overall, the Pelco NET5308T-EXP is an exceptional choice for organizations looking to modernize their surveillance technology without the need to overhaul existing infrastructure. With its multi-channel support, advanced compression technology, PoE capabilities, and intelligent alert systems, it represents a significant advancement in video surveillance technology, providing users with high-quality performance and flexibility.
Top Page Image Contents