49
7 Useful tips
English
FAQ
Question
Answer
My remote control does not | •• Check the antenna or cable connection to the main unit. | |
work. | •• Check the batteries of the remote control. | |
What should I do? | ||
•• Check if there is an obstacle between the infrared sensor window and the remote control. | ||
| ||
| •• Test the signal Output use IR Signal Check. ➠ p. 52 If okay, then possible infrared sensor trouble. | |
| •• Aim the remote control directly at the infrared sensor window on the front of the unit. | |
| •• Reduce the distance to the unit. | |
| •• | |
| •• When there is an | |
| the | |
| function. | |
How come the initial setup | •• Make sure to complete the initial setup before the unit goes into Standby mode. | |
appears every time I Turn On |
| |
this unit? |
| |
Why can I not watch some RF | •• Autoprogram must be completed when you set up the unit for the first time or move it to a location where previously unavailable | |
signal TV programs. | channels are broadcast. | |
| •• Make sure Autoprogram has been completed. ➠ p. 37 | |
| •• The selected channel may not be broadcasting. | |
| •• When Autoprogram is interrupted and not completed, some channels will not be received. Make sure to complete the | |
| Autoprogram. ➠ p. 37 | |
| •• The selected channel cannot be viewed by the Child and ratings lock setting. ➠ p. 34 | |
| •• The unit requires some kind of antenna Input. An indoor antenna (Digital or VHF / UHF), an external antenna (Digital or VHF / UHF) | |
| or an RF coaxial cable from your wall cable/satellite box needs to be plugged into the unit. | |
How come there is no image | •• Check if the correct Input mode is selected by pressing SOURCE. Watching channels from an external device ➠ p. 16 | |
from the connected external | •• Check the antenna, cable or other Input connection to the unit. | |
devices? | ||
•• When using the Component Video Connection check that the Green (Y), Blue (Pb/Cb) and Red (Pr/Cr) connectors are connected | ||
| ||
| to their corresponding colored jacks on the unit. | |
|
| |
When I enter a channel number, | •• Many Digital channels have alternate channel numbers.The unit changes the numbers automatically to the ones signifying the | |
it changes automatically. | broadcasting station channel number.These basic numbers used for previous Analog broadcasts. (e.g., Input ch# 30 automatically | |
| changes to ch# 6.1) | |
Why are captions not displayed | •• Captions that are delayed a few seconds behind the actual dialog are common for live broadcasts. Most captioning production | |
entirely? Or, captions are | companies can display a dialog to maximum of 220 words per minute. If a dialog exceeds that rate, selective editing is used to | |
delayed behind the dialog. | insure that the captions remain | |
How can I set the clock ? | •• There is no clock function on this unit. | |
|
| |
I cannot change the Child lock | •• Although the default PIN code (0000) is supplied with the unit, the PIN code will be required once you set a PIN code in Child | |
setting because my PIN code no | and ratings lock. ➠ p. 34 When you forget your PIN code, enter 0711 in Change PIN to reset the PIN code. ➠ p. 36 | |
longer works. |
|
Troubleshooting
If the unit does not perform properly when operated as instructed in this User Manual, check the following chart and all connections once before calling for service.
Symptom
Remedy
No power | •• Make sure the AC power cord is plugged in. |
| •• Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the AC outlet to ensure that the AC |
| outlet operates normally. |
| •• If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit to reset itself. |
|
|
Control buttons do not work. | •• Press only one button at a time. Do NOT press more than one button at the same time. |
| •• Ensure that no buttons on the remote control are depressed and move freely. |
|
|
Continued on next page.
