Setting the Start Time, Press the Cursor Right | Philips 55P8288

Features Menu • The Timer Control

11	12	1
10		2
9		3
8		4

75

6

SETTING THE START TIME

You can set the TV to turn itself on at a specific time, just as you

would an alarm clock. Follow these steps to set the Start Time.

BEGIN

Press the MENU button on the remote control to show the on-screen menu.

Press the CURSOR DOWN but- ton twice to highlight FEATURES.

Press the CURSOR RIGHT but- ton to enter the FEATURES menu.

Press the CURSOR RIGHT but- ton again. Then press the CURSOR

	PICTURE	TIMER
	SOUND	AUTOLOCK
	FEATURES	PIP		FEATURES
	INSTALL	CLOSED CAP		FEATURES		TIME

					TIMER
					TIMER
					AUTOLOCK	START TIME
					PIP	STOP TIME
					CLOSED CAP	CHANNEL
					FEATURES	ACTIVATE
						ACTIVATE



					TIMER
					TIMER

DOWN button once to highlight the START TIME control.

Press the CURSOR RIGHT

button again to highlight the time indicator area.

Press the NUMBER buttons to enter the correct time. If you make a mistake entering the time, use the CURSOR LEFT or RIGHT button to move among the time input slots to make corrections. NOTE: You can also use the CURSOR UP or DOWN button to cycle through digits to input the time.

Press the CURSOR UP or DOWN button to select AM or PM.

Press the i+ button to remove the

menu from the screen.

SMART HELP

You can set STOP TIME similarly to the way you set START TIME. Instructions are on

the next page.

8		AV	i+	SAP
8	TV	1	2	3
	VCR	1	2	3
	ACC	4	5	6
		4	5	6	6
		7	8	9	6
		7	8	9
1		SMART	0	SMART
			0

		MENU		SURF
				HOME
					3
				CH	4
				2	5
			4	2
		7	4	A/CH
		7
				PIP CH
			UP	DN

TIME			8:01 PM
START TIME
STOP TIME
CHANNEL
ACTIVATE
FEATURES
TIMER
	TIME
	START TIME		_ _:_ _
	STOP TIME
	CHANNEL
	ACTIVATE
	FEATURES
	TIMER
	TIME
	START TIME			8:00 AM
	STOP TIME
	CHANNEL
	ACTIVATE

14

Image 14

Philips 55P8288, 60P 8241, 55P8241, 60P8288 manual Setting the Start Time, Press the Cursor Right

Contents

Projection Television Warranty OwnerModel Verification Confirmation Registration Important Safety Instructions Table of Contents Features Digital-Ready Projection TV Adjusting the Picture Press the Cursor Right button Turning on the Dynamic Noise Reduction DNR Control Press the i+ button to remove Turning on the Imagemax Control Converge RED/BLUE Converge Multipoint RED/BLUE Navigate 1410 Press the i+ button to enter Undo Multipoint Press the Menu button to show Setting the Clock Press the Cursor Right button to enter the Features menu Setting the Start Time Press the Cursor Right Setting the Stop Time Selecting the Channel Press the Number buttons to Setting the Activate Control Constantly Displaying the Time on Screen Understanding Autolock Movie Ratings Enter a new four-digit code Setting UP the Access CodeThen press the Cursor Down Enter your new four-digit code Menu. Then press the Cursor Enter your four-digit AccessBlocking Channels Press the Cursor UP or Enter your four-digit Access CODE. Correct will flash very Blocking by Movie Rating Press the Cursor Down Enter your four-digit Access CodeBlocking by TV Rating Press the Cursor UP or Down button to select a rating Turning the Blocking Control on or OFF Press the i+ button to remove the menu Ton again to highlight Access Code Blocking Unrated Broadcasts Blocking Broadcasts That have no Rating Press the Cursor Right or Left button to turn no Rating Reviewing Your Settings Block Unrated No Rating Clearing ALL Blocked Channels Enter your four-digit Press the Cursor UP or Down button to select a Caption Using the Closed Captioning ControlLighted. Then press the Cursor Adjusting the TREBLE, BASS, and Balance Treble Using the AVL Audio Volume Leveler Control Using Incredible Surround Cursor Right or Left but Setting the TV for Stereo and SAP Setting the Audio OUT Control Using the TV Speaker Control and Audio Outputs Using the Bass Boost Control Press the Smartpicture button repeatedly to select either Using SmartpicturePress the Smartpicture Using Smartsound SmartSound Choices Using Surf and Alternate Channel Surf Using the Sleep Timer Control Using the Volume and AV Buttons Press the Volume +,- but Setting the TV Remote to Work Accessory Devices VCR Move the slide switch on the side Point the remote at the accessory Search Method VCR player stops, the correct code Setting the TV Remote to Work Accessories See the next page for more codes Satellite Receiver Brand Remote Codes Using PIP Basic Connections Using the PIP Remote Control Buttons Press the PIP ON/OFF button to Adjusting the PIP Color and Tint Controls Press the MENU/SELECT but More PIP Connections Helpful Hints Glossary of Television Terms Index Factory Service Locations Canada Houston Limited Warranty Projection Television