E9017FD_EN.qx3 03.8.6 10:13 AM Page 9
Setting Up your System
Automatic Channel Setup
You can programme the tuner to scan only the channels that you can receive in your area.
1Turn on the TV and select the video out channel on your TV.
2Press VCR, then DISC/VCR MENU.
3Press K/L to select TUNER SET UP, then press B.
4Press K/L to select AUTO TUN-
ING, then press B.
• The System distinguishes SECAM | PLEASE WAIT |
| |
or PAL automatically. |
|
• The tuner scans and memorizes START | FINISH |
all the active channels in your | ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ |
| |
area. After scanning, the tuner |
|
stops on the lowest memorized |
|
channel. |
|
5Press SKIP/P+ G / SKIP/P- H or numerical key pads to scan through channels you have received.
Manual Channel Preset
1Press VCR, then DISC/VCR MENU.
2Press K/L to select TUNER SET UP, then press B.
3Press K/L to select MANUAL
| TUNING, then press B. | MANUAL TUNING |
|
|
|
| |
4 | Press K/L to select SYSTEM, then | SYSTEM | [ L ] |
| press B to appear your desired | → PROG. | P55 |
| CHANNEL | 055 | |
| system. | DECODER | [OFF] |
5 | Press K/L to select PROG., then | SKIP | [OFF] |
|
|
press B. | SET=K L OR 0 – 9 | |
END=EXIT | ||
|
6Press K/L or numerical key pads
to select your desired programme number, then press B.
•You can select programme number
7Press K/L to select CHANNEL, then press B.
8Press K/L.The System tuner will begin to search up or down automatically.When a channel is found, the System will stop searching and the picture will appear on the TV Screen.
•You can select desired channel number by using numerical key pads.You must refer to the channel plan and press three digits to select the channel number. (To select channel 24, first press “0” button then press “2” and “4”).
•If this is the channel you want, press B.
•If you want to remove scrambled signals, press K/L to select DECODER.Then, press B to select [ON].
9Press DISPLAY/STATUS/EXIT to exit.
Notes:
– To confirm that a channel has been added, press the SKIP/P+ G / SKIP/P- H buttons.
– You should select the satellite channels to be received by the satellite receiver directly on the receiver itself.
Follow TV (Automatic TV channels sorting)
When the automatic channel search function is activated, the TV channels are saved in a specific order.This may vary from the order of TV channels on the TV.
This function changes the order of TV channels saved in the System to match that of the TV.
Make sure that the System and the TV are connected by a scart cable.
1 | Press VCR, then DISC/VCR MENU. | SELECT K L CHOOSE B | |
|
| ||
2 | Press K/L to select TUNER SET | AUTO TUNING | |
| UP, then press B. | MANUAL TUNING | |
| → FOLLOW TV | ||
3 | Press K/L to select 'FOLLOW TV' | ||
MOVE |
, then press B.
4'P:01' will appear in the System dis- END=EXIT play.
I cannot switch my TV set to programme number '1'
*If you have connected additional devices to socket AV2(DECODER), please disconnect these devices. Because of other connected devices, the TV set could switch to the pro- gramme number of the scart socket.
'NO TV SIGNAL' will appear in the TV screen.The System is not receiving a video signal from the TV.
Check the plug on the scart cable.
Check your TV's operating instructions to see which scart socket is used for video signals.
If this does not help, it's not possible to use this function. Please read the section 'Sorting and Clearing TV channels manually'.
5Select programme number '1' on the TV.
6Confirm with B on the System remote control.The System compares the TV channels on the TV and the System.
If the System finds the same TV channel as on the TV, then it stores it at 'P01'.
7Wait until the next number, e.g. 'P:02' appears in the display.
8Select the next programme number on the TV, e.g. '2'.
9Confirm with B.
10Repeat steps 7 to 9 until you have assigned a programme num- ber to all TV channels.
11To end, press DISPLAY/STATUS/EXIT.
English
9
