Bass/treble adjustment B/T Open state | Pioneer RS-D7R, RS-P90

Bass/treble adjustment <B/T> (Open state)

It is possible to select one from a choice of four frequencies to becomes the reference when adjusting the bass/treble tone. The frequencies and level adjustment ranges from which selections may be made are as follows:

Bass : 63 Hz, 100 Hz, 160 Hz, 250 Hz

Treble: 4 kHz, 6.3 kHz, 10 kHz, 16 kHz

Level adjustment range: –12 dB to +12 dB (1 dB/1 step)

1.Open the cover of the remote control (refer to page 5).

This switches to main menu setting screen.

2.Press the FUNCTION button 1.

The display switches to bass/treble adjustment screen.

3.Press the FUNCTION button 1 again to choose bass (BASS) or treble (TREB).

Pressing the button switches	BASS	TREB
bass/treble.

4.Press the 2/3 buttons and select a frequency point.

Tune to the desired frequency point.

5.Press the 5/∞ buttons and adjust the level.

Holding down these buttons continues their operations (with one stop at the central position).

Note:

•Raising the bass/treble level too high may result in distortion. Perform bass/treble adjustment to adjust overall sound quality.

Audio Adjustment <Main>

13

13

ENG/MASTER 96

Image 13

Pioneer RS-D7R, RS-P90 owner manual Bass/treble adjustment B/T Open state

Contents

RS-P90 Contents Display for the Person who Set Up Key Finder Remote control RS-D7RHead unit RS-D7R Closed state Open state Remote control Menu display Opening and closing the remote control coverKey Finder When the cover is open When the cover is closedWhen the cover is closed in the middle of operation Menu display in closed state Key Finder / Before Using This Product Before Using This ProductAbout this unit Case of trouble About this manualProduct registration About the digital network Before Using This Product Remove the covering Resetting the microprocessor Switching to the audio menu Audio AdjustmentAudio menu Balance adjustment FAD/BAL Control Closed state Audio Adjustment MainSwitching to the main menu Main menu Bass/treble adjustment B/T Open state Press the Function button To select the setting Using the compression CP Open state Using the position selector Posi Adjusting the listening position PS Open stateButton Position Experimenting with other positions Use the position selector function and select the position Fine tuning the position Points concerning fine tuning Time alignment adjustment function of the network menu Relation to time alignment adjustment function Increase or decrease the level with the 5/∞ buttons Source level adjustment SLA Open state About the equalizer menu Audio Adjustment EqualizerBand graphic equalizer 31B-GEQ Band parametric equalizer 3B-PEQ Equalizer menu Switching to the equalizer menu Relation between frequency characteristics and sound quality Points when adjusting the equalizer curve Switch between right and left to set up the equalizer curve Adjusting the 31 band graphic equalizer Fine Open stateWhen completing the adjustment About the adjustment using the parametric equalizer Adjusting the 3 band parametric equalizer Fine Open stateSeparate 3 band adjustment for left/right Select function Setting the equalizer curve Switch between left and right to set up the equalizer curve Adjust other bands Common to 31B-GEQ and 3B-PEQ Flat function FLT Open state Clear function CLR Open state What is the multi-amp system? Audio Adjustment Network To cancel the network menu, press the Band button Switching to the network menuAudio Adjustment Network Network menu N.W Switching to the time alignment adjustment mode Time alignment adjustment T.A. Open stateMeasuring the distance to be corrected Delay Time Unit of distance must be centimeters Network Press Function buttons 1 or 2 and select the band to input Inputting the distance to be corrected Delay Time Audio Adjustment Network Range Cut-off frequency Level adjustment H.P.F L.P.F Filter adjustment FTR Open state Using the mute function MUT Switching to the filter adjustment modeAbout the H.P.F. and L.P.F About the slope Adjusting the filter Press Function button 3 and adjust the slope of each filter Press the 5/∞ buttons Adjust the level of each bandPress Function button 4 and adjust the phase of each band Switch between left and right channel to adjust the filter For better frequency characteristics Important points in adjusting the slopeAdjusting the subwoofer effectively Adjusting the low-range effectively Minimum delay phase characteristics Minimum phase MIP Linear phase characteristics Linear phase LIN Memory functions of adjusted audio menu Memo Audio Adjustment Memory FunctionsBase memory Custom memory Audio Adjustment Memory Function Switching to memory modeEqualizer menu Network menu Adjust each audio menu Storing the adjustment data in memorySwitch to the memory mode of each menu refer to Press the Shift button to cancel memory mode Recalling data stored in memory Close the cover of the remote controlForward/reverse order Functions of equalizer menu Specifying the memory number directly Press the Function button to recall the memory Specifying the memory number directlyMemory recall operations on the equalizer menu Memory protect function When turning the protect function ON/OFFRecall the memory refer to Inputting characters Switching to the edit mode Display for the Person who Set Up the Audio AdjustmentsPress the Menu button to switch to the audio menu Inputting the name Switch the desired character type with Function button When removing the car battery Equalizer Memory Data Memo Network Filter characteristics Memory Data Memo Network Time alignment Connecting the Units Using the corrugated tube Setting exampleConnecting the Units Routing the optical cable RS-D7R Connection diagram Connecting the RCA input amplifier Connecting the leads Connecting the power terminal Attach the cable clamp Secure the optical cable Installing the unit InstallationInstall the brackets to the bottom of the unit Install the unit to the vehicle Checklist TroubleshootingInstallation / Troubleshooting Symptom Cause Remedy General Specifications Specifications Pioneer Corporation