12

The Other Setup menu

The Other Setup menu is where you can make customized settings to reflect how you are using the receiver.

1 Press on the remote control, then press HOME MENU.

AGraphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the screens and select menu items. Press RETURN to exit the current menu.

2Select ‘System Setup’ from the Home Menu.

3Select ‘Other Setup’, then press ENTER.

4Select the setting you want to adjust.

If you are doing this for the first time, you may want to adjust these settings in order:

!Auto Power Down – Sets the power to turn off automatically when the receiver is not being used.

!Volume Setup – Sets up the volume-related operations of this receiver (page 102).

!Remote Control Mode Setup – Sets this receiver’s remote control mode (page 102).

!Software Update – Use to update the receiver’s software and check the version.

!ZONE Setup – Use to make the sub zone-related settings (page 103).

!EXTENSION Setup – Allows the CU-RF100 to be used even when the receiver is in the standby mode (page 104).

!On Screen Display Setup – Sets whether or not to display the status on the display when the receiver is oper- ated (page 104).

!SC-68 only:

Multi Ch In Setup – Specifies the optional settings for a multi-channel input (page 104).

!Maintenance Mode – This is used to receive maintenance from a Pioneer service engineer or custom installer (page 104).

5Make the adjustments necessary for each setting, pressing RETURN to confirm after each screen.

Auto Power Down

The power can be set to turn off automatically if no operation has been performed for a specific amount of time with no audio or video signals being input to the receiver. When using ZONE 2 or ZONE 3, the ZONE 2 or ZONE 3 power can also be set to turn off, but for ZONE 2 or ZONE 3 the power turns off automatically after the amount of time set here even if signals are being input or operations have been performed.

Different times can be set for the main zone, ZONE 2 and ZONE 3.

1Select ‘Auto Power Down’ from the Other Setup menu.

2Select the zone you want to set and set the time after which the power turns off.

!MAIN – The time can be selected from among “15 min”, “30 min”, “60 min” and “OFF”. The power turns off after there has been no signal and no operation for the selected time.

!ZONE 2 – The time can be selected from among “30 min”, “1 hour”, “3 hours”, “6 hours”, “9 hours” and “OFF”. The power turns off after the selected time.

!ZONE 3 – The time can be selected from among “30 min”, “1 hour”, “3 hours”, “6 hours”, “9 hours” and “OFF”. The power turns off after the selected time.

!ZONE 4 – The time can be selected from among “30 min”, “1 hour”, “3 hours”, “6 hours”, “9 hours” and “OFF”. The power turns off after the selected time.

Note

!Depending on the connected devices, the Auto Power Down function may not work properly due to excessive noise or other reasons.

The System Setup and Other Setup menus

Volume Setup

You can set the maximum volume of this receiver or specify what the volume level will be when the power is turned on.

1Select ‘Volume Setup’ from the Other Setup menu.

2Select the Power ON Level setting you want.

The volume can be set so that it is always set to the same level when the receiver’s power is turned on.

!LAST (default) – When the power is turned on, the volume is set to the same level as when the power was last turned off.

!“---” – When the power is turned on, the volume is set to minimum level.

!–80.0dBto +12.0dB – Specify the volume to be set when the power is turned on, in steps of 0.5 dB.

It is not possible to set a volume level greater than the value specified at Volume Limit setup (see below).

3 Select the Volume Limit setting you want.

Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by operating VOLUME button (or the dial on the front panel).

!OFF (default) – The maximum volume is not limited.

!–20.0dB/–10.0dB/0.0dB– The maximum volume is limited to the value set here.

4 Select the Mute Level setting you want.

This sets how much the volume is to be turned down when MUTE is pressed.

!FULL (default) – No sound.

!–40.0dB/–20.0dB– The volume will be turned down to the level specified here.

5When you’re finished, press RETURN.

You will return to the Other Setup menu.

Remote Control Mode Setup

!Default setting: 1

This sets this receiver’s remote control mode to prevent erroneous operation when multiple units of the receiver are being used.

1Select ‘Remote Control Mode Setup’ from the Other Setup menu.

2Select the Remote Control Mode setting you want.

3Select ‘OK’ to change the remote control mode.

4Follow the instructions on the screen to change the remote control’s setting.

See Operating multiple receivers on page 83.

5When you’re finished, press RETURN.

You will return to the Other Setup menu.

Software Update

Use this procedure to update the receiver’s software and check the version. There are two ways to update: via the Internet and via a USB memory device.

Updating via the Internet is performed by accessing the file server from the receiver and downloading the file. This procedure is only possible if the receiver is connected to the Internet.

Updating via a USB memory device is performed by downloading the update file from a computer, reading this file onto a USB memory device then inserting this USB memory device into the USB port on the receiver’s front panel. With this procedure, the USB memory device containing the update file must first be inserted into the USB port on the receiver’s front panel.

102