10

4 Repeat steps 2 through 3 for the other components you want to control.

To try out the remote control, switch the component on or off (into standby) by pressing uSOURCE. If it doesn’t seem to work, select the next code from the list (if there is one).

5 Press RCU SETUP to exit the preset setup mode.

Programming signals from other remote controls

If the preset code for your component is not available, or the available preset codes do not operate correctly, you can program signals from the remote control of another component. This can also be used to program additional operations (buttons not covered in the presets) after assigning a preset code.

The remote can store about 120 preset codes from other components (this has been tested with codes of Pioneer format only).

Certain buttons represent operations that cannot be learned from other remote controls. The buttons available are shown below:

RECEIVER ALL ZONE STBY

SOURCE

 

 

 

 

 

DISCRETE ON

 

 

 

 

 

 

RCU SETUP

 

 

 

 

 

 

 

BDR

 

 

 

 

 

BD

DVD

DVR

HDMI

 

 

 

 

 

 

 

 

 

FEATURES

 

TV

CD

NET

ADPT

PHASE

PQLS

Hi-Bit

D.FILT

 

 

 

 

USB

CBL

 

 

MPX

BAND

PTY

iPod

SAT

MHL

TUNER

 

 

 

 

INPUT SELECT

STATUS RECEIVER

PRESET

TUNE

 

 

 

 

 

 

 

 

AUTO/ALC/

 

 

THX

 

 

 

VOLUME

DIRECT

STANDARD ADV SURR +Favorite

 

INPUT

1

2

3

AUDIO

 

 

 

 

SIGNAL SEL

MCACC

CH LEVEL

AUTO

TV CONTROL

 

 

S.RTRV

 

 

4

5

6

DISP

 

 

 

 

CH

VOL

 

SPEAKERS

DIMMER

SLEEP

 

MUTE

7

8

9

CH

 

 

 

 

 

 

 

D.ACCESS HDMI OUT

CLASS

 

AUDIO

 

 

VIDEO

/CLR

0

ENTER

CH

PARAMETER

 

 

PARAMETER

ZONE 2

ZONE 3

ZONE 4

LIGHT

 

 

 

 

 

 

 

 

Z2

Z3

Z4

 

TOP MENU

 

 

TOOLS

 

 

 

 

 

 

 

MENU

 

 

 

 

 

ENTER

 

 

 

 

 

HOME

 

 

RETURN

 

 

 

 

MENU

 

 

 

RECEIVER

 

 

 

 

 

 

 

iPod CTRL

 

 

 

 

 

 

 

1Press and hold RCU SETUP, then press ‘2’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

!To “learn” codes at the TV CONTROL buttons, proceed to step 3.

!To cancel the preset setup mode press RCU SETUP.

2Press the input function button for the component you want to control.

The LED blinks once and flashes continuously.

3Point the two remote controls towards each other, then press the button that will be doing the learning on this receiver’s remote control.

The LED flashes once, then stops flashing, remaining lit.

Controlling the rest of your system

!The remote controls should be 3 cm (1 inch) apart.

 

3 cm

 

This receiver’s

(1 inch)

Other remote

 

remote control

 

control

4Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver’s remote control.

If the LED lights for one second and continues to flash, the setting has been successfully completed.

!If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one input function on page 85 to erase a programmed button you’re not using to free up more memory (note that some signals may take more memory than others).

!Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.

!Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.

5To program additional signals for the current component repeat steps 3 and 4.

To program signals for another component, exit and repeat steps 2 through 4.

6 Press RCU SETUP to exit the programming mode.

Erasing one of the remote control button settings

This erases one of the buttons you have programmed and restores the button to the factory default.

1Press and hold RCU SETUP, then press ‘7’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

!To erase operations registered at the TV CONTROL buttons, proceed to step 3.

!To cancel the preset setup mode press RCU SETUP.

2Press the input function button corresponding to the command to be erased.

The LED flashes once.

3Press and hold the button to be erased for three seconds.

If the LED lights for one second, the erasing has been successfully completed.

4Repeat step 3 to erase other buttons.

5Press RCU SETUP to exit the erasing mode.

84