Operating Environment | Pioneer VSX-1016V-S, VSX-1016V-K specs

D3-4-2-1-7c_A_En

K041_En

D3-4-2-2-1a_A_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

Operating Environment

Operating environment temperature and humidity:

+5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

CAUTION

The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a_A_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

Image 3

Pioneer VSX-1016V-S, VSX-1016V-K manual Operating Environment

Contents

VSX-1016V-SVSX-1016V-K Risk of Electric Shock Do not Open Important the Moulded Plug Operating Environment Contents Controlling the rest of your system Other SettingsUsing other functions Other connections Checking what’s in the box FeaturesBefore you start Before you start Chapter Loading the batteries Before you start Installing the receiver Introduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide Chapter Speaker configuration in the OSD Minute guideWait for the test tones to finish then confirm Playing a source Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guide Connecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter VSX-1016V Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box DVD player DVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connection Connecting digital audio sources Use a three-way component video cableCD-R, MD, DAT, etc Tape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoder Connecting the speakers Connecting your equipment Installing your speaker system Placing the speakers Bare wire connections THX speaker system setup Connecting antennas Connecting external antennas Plug the power cord into a power outletPlugging in the receiver Controls and displays Controls and displays ChapterFront panel Controls and displays Operating range of remote control unit Sleep Controls and displays DisplayOver / ATT Video Conv Select Controls and displays Remote controlReceiver Input Select Mute Multi OPEShift Source Standard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround sound Listening to your system Using the Home THX modesUsing the Advanced surround effects Setting the effect options Use the +/- buttons to set it as necessary Press EFFECT/CH SEL again to adjust other settingsListening in stereo Listening with Acoustic Calibration EQ Using the Virtual Surround Back mode Listening to your system Choosing the input signal Press Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controls Basic playback controls Using the USB interfaceUSB playback USB playback Chapter About WMA USB playbackOther compatibility information About MPEG-4 AAC Listening to the radio Using the tunerUsing the tuner Chapter Saving station presets An introduction to RDS Using the tunerNaming station presets Listening to station presets Using EON Displaying RDS informationPress Disp for RDS information Surround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menu Fine Channel Level System Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menu Acoustic Calibration EQ System Setup menuSetting the Acoustic Calibration EQ automatically Fine Speaker Distance Copying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Manual speaker setup Speaker SettingChecking your Acoustic Calibration EQ settings Channel Level Select ‘Channel Level’ from the Manual SP Setup menuSelect a setup option Confirm your selected setup option Adjust the distance of each speaker using THX Audio SettingSelect ‘THX Audio Setting’ from the Manual SP Setup menu Select ‘Speaker Distance’ from the Manual SP Setup menu THX Speaker Setup Select ‘THX Speaker Setup’ from the Manual SP Setup menuSpecify whether or not you are using a THX speaker system About Hdmi Connecting using HdmiOther connections Other connections Chapter Other connections Second Zone speaker B setupConnecting the multichannel analog inputs Switching the speaker system Connect your speakers as shown below Bi-wiring your speakersConnecting additional amplifiers Bi-amping your front speakers Using this receiver with a Pioneer plasma display If you have a Pioneer plasma display, you can use anLarge Audio Using the SR+ mode with a Pioneer plasma displayDVD player DVD/LD Assigning the digital inputs Other SettingsOther Settings Chapter Input Assign menu Dual Mono Setup Other SettingsOther Setup menu Dynamic Range Control Setup LFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVideo Converter Setup Making an audio or a video recording Using other functionsUsing other functions Chapter Reducing the level of an analog signal Display shows RESET? Using other functions Using the sleep timerResetting the system Switching the speaker impedance Controlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controls Controlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codes Programming a multi-operation or a shutdown sequence Renaming input source namesMulti Operation and System Off Direct function Using System off Using multi operations Controls for other components Controlling the rest of your system Controls for TVs Decide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensor Additional information Chapter TroubleshootingPower Additional information Additional information Other audio problems Video Settings Display Remote control Hdmi USB interface Additional information Surround sound formats DolbyWindows Media Audio 9 Professional About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games Mode Auto Multichannel signal formats Cleaning the unit Additional information Specifications Additional information Additional information Pioneer Corporation