Pioneer VSX-1016V-S Other Settings Chapter, Input Assign menu, Assigning the digital inputs

Other Settings

Chapter 10:

Other Settings

The Input Assign menu

You only need to make settings in the Input Assign menu if you didn’t hook up your digital equipment according to the default settings for the digital inputs, or if you have connected equipment using component video cables.

1Press RECEIVER on the remote control, then press the SETUP button.

An on-screen display (OSD) appears on your TV. Use and ENTER to navigate through the screens and select menu items. Press RETURN to confirm and

exit the current menu.

2Select ‘Input Assign’ from the System Setup menu.

System Setup				5.Input Assign
	1.Surr	Back System
					a.Digital Input
	2.Auto	MCACC			b.Component Input
	3.Manual		MCACC		c.HDMI Input
	4.Manual		SP Setup
	5.Input	Assign
	6.Other	Setup
			￿ : Exit		￿:Return

Assigning the digital inputs

•Default settings: Coaxial - 1 – DVD

Coaxial - 2 – DVR 2

Optical - 1 – DVR 1

Optical - 2 – TV

Optical - 3 – CD

You only need to do this if you didn’t hook up your digital equipment according to the default settings for the digital inputs (see above). This setting tells the receiver what digital equipment is hooked up to which terminal so the buttons on the remote correspond to what you have hooked up.

1 Select ‘Digital Input’ from the Input Assign menu.

5.Input Assign		5a.Digital Input		Setup
		Coaxial - 1
	a.Digital Input			DVD/LD
	b.Component Input	Coaxial - 2	[	DVR 2	]
	c.HDMI Input	Optical - 1	[	DVR 1	]
		Optical - 2	[ TV/SAT ]
		Optical - 3	[	CD	]
	￿:Return			￿:Finish

2Select the number of the digital input to which you’ve connected the digital component.

The numbers correspond with the numbers beside the inputs on the back of the receiver.

3Select the component that corresponds with the one you connected to that input.

Select between DVD, TV, CD, CD-R, DVR 1, DVR 2 or OFF.

10

• Use and ENTER to do this.

•If you assign a digital input to a certain function (for example, DVD/LD) then any digital inputs previously assigned to that function will automatically be switched off.

4When you're finished, press RETURN. You return to the Input Assign menu.

Assigning the component video inputs

•Default settings: Component 1 – OFF

Component 2 – OFF

Component 3 – OFF

If you used component video cords to connect your video equipment you must tell the receiver which device it is, or else you may see the S-video or composite video input instead of the component video signal. For more on this, see Using the component video jacks on page 14.

1Select ‘Component Input’ from the Input Assign menu.

5. Input Assign		5b.Component	Input
	a.Digital Input	Component - 1
				DVD/LD
	b.Component Input	Component - 2	[	TV/SAT	]
	c.HDMI Input	Component - 3	[	DVR 1 ]
	￿:Return			￿:Finish

2Select the number of the component video input to which you’ve connected your video component.

The numbers correspond with the numbers beside the inputs on the back of the receiver.

3Select the component that corresponds with the one you connected to that input.

Select between DVD, TV, DVR 1, DVR 2 or OFF.

• Use and ENTER to do this.

•Make sure you have made audio connections from the component to the corresponding inputs on the rear of the receiver.

•If you connect any source component to the receiver using a component video input, you should also have your TV connected to this receiver's component video MONITOR output (downconverting component video is not possible after assigning an input).

4When you're finished, press RETURN. You return to the Input Assign menu.

49

En