Pioneer VSX-D810S, VSX-D850S, VSX-D710S manual Displays & Controls, Master Volume

05Displays & Controls

Front Panel			7 (VSX-D710S DVD5.1CH button)
1 2	3	4 5 6 8 9 0 - = ~
		N∫m-Û˘,?∫		1
(	* & ^ % $ #		@	!

1STANDBY indicator

Lights when the receiver is in standby mode (note that the receiver consumes a small amount of power (1W) in standby mode).

2 STANDBY/ON button

Switches the receiver between on and standby (note that the receiver consumes a small amount of power (1W) in standby mode).

3STATION (+/–) buttons (see pages 32-33) Selects station memories when using the tuner.

4TUNING (+/–) buttons (see pages 32-33) Selects the frequency when using the tuner.

5DIRECT button

Use to switch DIRECT playback on or off. This mode bypasses the tone controls, channel levels, 2/DTS

and DSP modes for the most accurate reproduction of a program source.

6MONITOR button

Press to switch tape monitoring on/off.

7DIGITAL NR button (VSX-D810S/D850S) Switches the DIGITAL NR on or off .

DVD5.1CH button (VSX-D710S) (see page 31) On the VSX-D810S/D850S use this button to switches the DIGITAL NR on or off. On the VSX- D710S this button switches between DVD5.1CH

input and regular DVD input.

8DSP MODE button (see page 28, 30)

Use to switch between the various DSP modes available (HALL1, HALL 2, JAZZ, DANCE,

THEATER1, THEATER 2, 6CH STEREO [VSX- D810S/D850S only]) and DSP off. Use this button to create different surround sound effects from

any stereo source.

9Remote sensor

Receives the signals from the remote control.

0SIGNAL SELECT button (see page 29)

Use to select an analog or digital or AUTO (VSX-

D810S/D850S only) signal.

-2/DTS button (see pages 27, 29)

22Use to switch between the various Dolby/DTS

=TONE button

This button allows you to activate the BASS & TREBLE controls. To adjust the BASS and/or TREBLE use the MULTI JOG DIAL. Tone can only be used in 2 channel stereo sound mode. The tones controls have no effect on the B speaker system.

~MULTI JOG dial

You can use this dial for two purposes. Firstly, in normal mode turn it to select a source component. Secondly, use it to adjust the BASS and/or TREBLE levels when the TONE button has been activated (as explained above).

!MASTER VOLUME

Use to set the overall listening volume.

@VIDEO INPUT jacks

Connect a video camera, video game system, etc. to the VIDEO INPUT jacks (refer to page 10).

#MIDNIGHT button (see page 31)

Use when listening to movie soundtracks at low volume. This feature will enable you to hear quiet sounds and not get jolted by loud or sudden sound effects.

$SPEAKERS button

Use to switch the speaker system A = B = A+B = off. In B and A+B speaker modes you hear only 2 channel stereo sound.

%MPX button (see page 32)

lf the TUNED or STEREO indicators don't light when tuning to an FM station because the signal is weak, press the MPX button to switch the receiver into mono reception mode. This should improve the sound quality and allow you to enjoy the broadcast.

^BAND button (see page 32-33) Press to select the AM or FM band.

&MEMORY button (see page 33)

Press to memorize a station for recall using the STATION (+/–) buttons.

*CLASS button (see pages 33)

Switches between the three banks (classes) of station memories.

( PHONES jack

Use to connect headphones but this does not switch

En

surround modes.

the speakers off.