Pioneer VSX-D710S manual Press Setup and hold for three seconds, To cancel Learning setup mode

Controlling the Rest of Your System

Learning Mode: Programming Signals from other Remote Controls

If preset codes are not available for your component(s), or the available preset codes do not operate correctly, you can use this function to program in signals from the remote control(s) of your other component(s). This operation can also be used after recalling a preset code to program additional operations not covered in the preset codes.

SOURCE		RECEIVER		VSX-D710S/
				4 D810S only
LED
DVD	TV	VCR	CD-R	3
	MULTI CONTROL
RCV	CD	TUN	TVC
1	2		3
MIDNIGHT	5.1 / 7.1		ATT
4	5		6
		EFFECT
7	8		9
10			DISC
	0		ENTER
DTV INFO MPX/RETURN		D.ACCESS	GUIDE
¶	7	3	8
BAND	CLASS	DTV ON/OFF DTV MENU
1	¡	4	¢
2/DTS	DSP	TEST TONE	SIGNAL SELECT
CH SELECT	CH LEVEL		FUNCTION

LOUDNESS FL DIMMER SETUP MUTING 1,7

TUNE

ST		ST	2
	ENTER

TUNE

VSX-D850S only

CHANNEL

VOLUME MASTER VOLUME

MENU

TVFUNC

TV

TV CONTROL

AV PRE-PROGRAMMED AND LEARNING

REMOTE CONTROL UNIT

1Press SETUP and hold for three seconds.

The LED on the remote control will light for two seconds.

To cancel the Learning mode at any time Press SETUP.

The remote control will also return to the previous mode after thirty seconds of inactivity.

2VSX-D850S only: Use the @ # buttons to select the Learning mode.

The Learning mode is indicated by the Learning icon (LEARN) in the remote’s LCD display.

3Press the MULTI CONTROL button for the component you want to control

4VSX-D710S/D810S: Press and hold the RECEIVER button for two seconds to start the Learning mode.

The LED lights steadily.

To cancel LEARNING setup mode

Press SETUP for one second.

If no commands are entered within thirty seconds the

38remote will revert to its previous mode.

En

5Point the two remote controls towards each other. Press the button to be learned on this receiver’s remote control (for example the 3

[play] button).

1 - 2 inches	3	6	9	8	¢
				3	4
	2	5	8	0
				7	¡
	1	4	7		1
				¶

Point the remote controls directly at each other, about 1-2 inches apart, and press the button on the remote control for the operation you want to program. The LED flashes rapidly. For VSX-D850S, the LEARN icon blinking.

6Press the corresponding button on the other remote control to be taught to this receiver’s remote control (in the above example the 3

[play] button).

Point the remote controls toward each other. Press the button on the other remote control corresponding to the operation you wish to program. The LED on this receiver’s remote will go out and then resume a steady light if the operation is learned. (For VSX-D850S model the LEARN icon will light steadily and the LCD display will show “OK” if the operation has been learned.) If the operation hasn’t been learned for some reason the LED will blink for three seconds and then light steadily. (For VSX- D850S model the LCD will display “error” if the operation hasn’t been learned.)

If this happens press the teaching key repeatedly, varying the distances between the remotes, until you see the LED on this unit’s remote light steadily, without blinking first.

To program additional operations for the current component

Repeat steps 5 and 6.

To program operations for another component Repeat steps 2 through 6 (VSX-D850S).

Repeat steps 3 through 6 (VSX-D710S/D810S).

7Press and hold SETUP for one second to exit the LEARNING setup mode.

After thirty seconds of inactivity the remote control will automatically leave the LEARNING mode and revert to its previous mode.

MEMO:

•Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.

•Certain buttons represent modes that cannot be learned from other remote controls. These include:

RCV, CH SELECT, CH LEVEL, FUNCTION LOUDNESS, FL DIMMER, and MUTING.

• TV CONTROL buttons ( TV , VOL +/-, and TV FUNC ) can only be learned in TV & TVC mode.