QS464

FRONT PANEL

1

 

 

 

 

 

 

 

 

 

 

 

2

3

4

5

6

7

8

REAR PANEL

 

 

 

 

 

 

 

 

 

1

2

3

4

5

QS464

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

 

 

 

 

 

 

 

 

 

 

 

MENU

 

 

 

OK

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

6

7

8

9

0

 

 

 

 

 

 

 

 

 

REC ALARM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USB 2.0

USB MOUSE

ON/OFF

 

 

 

 

 

 

AUDIO OUT

VIDEO IN

 

AUDIO IN

 

 

 

1

3

1

-

+

 

 

 

 

DC +12V

 

2

4

2

VIDEO OUT

 

 

 

IN

 

 

 

 

6 7

 

 

 

 

 

RJ45

485A

485B

 

 

 

VGA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 9 10

Item #

Name/ Symbol

Description

 

 

 

1

STANDBY

Press to set the system in standby mode. Press again to wake.

 

 

 

2

 

Press buttons 1-4 to view that channel full-screen

 

 

Press buttons 1-0 to input passwords and user IDs.

DURING PLAYBACK PRESS:

◄◄Increase reverse playback speed 1X, 2X, 4X.

 

CHANNEL/

 

Press to freeze playback to one frame, then press

 

NUMBERS/

n/again to advance frame-by-frame.

 

PLAYBACK

 

 

 

Press to start playback

 

 

 

 

►►

Press to slow playback speed by 1/2, 1/4, 1/8.

 

 

►►

Press to increase forward playback speed 1X, 2X,

 

 

4X.

3

MENU/EXIT

Press to open/close the main menu.

 

 

 

 

4

IR SENSOR

IR Receiver for remote control.

 

 

 

 

5

LED

Shows recording status and motion detection (Alarm).

 

INDICATORS

 

 

 

 

 

 

6

 

Press to move cursor up; in PTZ mode, press to pan

 

 

camera up.

 

 

Press to move cursor down; in PTZ mode, press to

 

NAVIGATION

pan camera down.

 

Press to move cursor left; in PTZ mode, press to pan

 

 

 

 

camera left.

 

 

Press to move cursor right; in PTZ mode, press to

 

 

pan camera right.

7

 

In menus, press to confirm selections; in PTZ mode, press to

 

OK

change the navigation buttons to control a connected PTZ

 

 

camera (not included)

 

 

 

 

8

 

USB

The upper port is to connect a USB flash drive for

 

 

 

data backup and firmware upgrades.

 

 

 

The lower port is to connect a USB mouse.

 

 

 

 

Item #

Connector

Description

 

 

 

1

Power Switch

Power On/Off

 

 

 

2

AUDIO

For connection to amplified speaker

OUTPUT

 

 

 

 

 

3

VIDEO IN

Video input for connecting analog video signal input (BNC)

 

 

 

4

AUDIO IN

Audio input for connecting audio signal (2 feeds)

 

 

 

5

NETWORK

For connecting Ethernet cable

 

 

 

6

 

DC 12V Power Connection

 

 

 

7

VIDEO OUT

Video output for connecting TV (BNC)

 

 

 

8

RS485

RS485 for connecting PTZ

 

 

 

9

USB

Mouse port

 

 

 

10

VGA OUTPUT

To connect to VGA monitor

 

 

 

18

19

Page 10
Image 10
Q-See QS4474 user manual QS464, Item # Name/ Symbol Description, During Playback Press