WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front.
Replace Control Panel in reverse order and test for ignition.
5. To Remove Clock
Disconnect from electricity supply.
Remove the Control Panel (See 2). Pull off the timer control button(s).
Remove the timer/mounting bracket assembly from the control panel by removing the fixing screws.
Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case, at the same time pulling the unit forward.
Reassemble in reverse order. When replacing leads refer to the wiring diagram. Check operation of timer.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS TURN OFF GAS SUPPLY.
6. To Remove a Thermostat
Remove control panel and appropriate hotplate tray. Open oven door. Remove oven furniture.
Main (RH) oven
Remove thermostat phial cover (2 screws). Unclip the thermostat phial from the clips in the oven back.
Tall oven
Remove the oven inner back see 18. Unclip the thermostat phial from the clips in the oven back.
Feed the thermostat capillary out of the oven. Disconnect wiring from thermostat. Remove 2 screws holding thermostat to mounting panel. Fit new thermostat and reassemble in reverse order. Ensure that the phial is clipped to the oven back with the phial centrally positioned between the clips.
Check operation of thermostat.
7. To Change Grill Control Tap
Remove the facia panel, see 2. Lift up the RH hotplate tray front (see 2). For LP cookers, unplug the FSD lead from the rear of the tap. Undo the gas connection to rear of valve and remove the screw(s) securing tap to gas rail. Remove old tap, discard old gasket/seal. Fit new gasket/seal to new tap.
Reassemble in reverse order. Check tap is adjusted for correct gas. Check appliance is gas sound.
8. To Change Control Taps
Remove the Control Panel (see 1). Lift up the appropriate hotplate tray front (see 2).
Undo compression fitting at the rear of the tap. Remove the fixings that secure the tap to the gas rail. Remove the tap. Remove and discard the gasket seal. Fit new gasket seal to replacement tap.
9. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new injector. Reassemble in reverse order. Check appliance is gas sound.
10. To Change Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the screw holding the electrode. Pull electrode vertically up sufficiently to grip the lead between thumb and forefinger. Pull off the electrode, but keep hold of the lead. Fit new electrode to the lead. Fix electrode in burner with screw. Replace burner cap. Check the burner ignition. Replace pan supports.
11. To Remove or Change a Hotplate Burner.
Remove the hotplate tray (see 2).
LH hotplate burners
Remove heat shield (2 screws). The burners are mounted in 2’s on cross supports. Disconnect the burner feed pipes at the burners. Remove the screw on the right holding the cross support. Slide the support to the right to release in from the left hand location. Lift the cross support and burners clear. The burners are fixed to the cross supports with 2 screws. Remove the appropriate burner and fit the new one. Reassemble in reverse order. Check burner operation is satisfactory.
RH Wok burner
Disconnect the burner feed pipes at the burner. Fit the new one and reassemble in reverse order. Check burner operation is satisfactory.
12. To Change Grill Injector
Remove the hotplate control panel, see 1.
spring clip
grill injector holder
Lift up the spring clip retaining the grill injector holder and slide the injector holder out of the burner venturi. Remove grill jet from adaptor and fit new jet (see table below for correct jet). Put the injector holder back in the burner venturi.
32
