Manuals / Raypak / Household Appliance / Boiler

Raypak 0180B Type H manual Heating, Piping Connections, Input, Capacity, I=B=R, Rating, Gas NPT

Models: 0180B Type H

1 40

Page 6

		Heating	Net	Piping Connections					K
Model	Input	Heating	Net						K
Model	Input	Capacity	I=B=R			A	B	C	Vent
No.	MBH	Capacity	I=B=R	Water		A	B	C	Vent
No.	MBH	MBH	Rating	Water	Gas NPT				Dia.
		MBH	Rating	NPT	Gas NPT				Dia.
				NPT

H-0042	42	35	30	1 in.	1/2 in.	11 in.	5 3/4 in.	5 1/2 in.	4 in.

H-0066	66	54	47	1 in.	1/2 in.	11 in.	5 3/4 in.	5 3/4 in.	5 in.

H-0090	90	74	64	1 in.	1/2 in.	11 in.	5 3/4 in.	5 3/4 in.	5 in.

H-0135	135	109	95	1 1/4 in.	1/2 in.	18 in.	6 1/4 in.	6 1/4 in.	6 in.

H-0180	180	148	129	1 1/4 in.	1/2 in.	18 in.	6 1/4 in.	8 in.	7 in.

Table A: Specifications

	B			16
AUTOMATIC				1
AUTOMATIC	K			4/2
VENT DAMPER	K			4/2
(FIELD INSTALLED)
		INLET		C
				C
	31/8		117/8
OUTLET
			6
			MIN
				331/4
			19	THERMOSTAT CONN	31/4
			19	(ELECTRICAL CONN
				(ELECTRICAL CONN
				ON OTHER SIDE)	GAS
					GAS
					CONN
	A			221/8
				261/2

3/4 NPT PIPE TO DRAIN

121/2

Fig. 1: Dimensions

Page 6

Image 6

Raypak 0180B Type H manual Heating, Piping Connections, Input, Capacity, I=B=R, Rating, Gas NPT

Contents

Do not try to light any appliance Models 0042B, 0066B, 0090B 0135B & 0180B - Type HWHAT TO DO IF YOU SMELL GAS INSTALLATION & OPERATING INSTRUCTIONSPage GENERAL SPECIFICATIONS CONTENTSTROUBLESHOOTING INSTALLATIONDANGER WARNINGSPay Attention to These Terms WARNING-CALIFORNIAPROPOSITIONGENERAL SPECIFICATIONS RECEIVING EQUIPMENTInput HeatingPiping Connections CapacityMounting Base INSTALLATIONCode Requirements Clearance RequirementsSq. in. of Free Area Combustion/Ventilation AirModel No Model NoVent Venting ConnectionsConnector Model NoCommon Vents Roof Pitch X/12H Min. ft Vent Damper Installation Location Mounting Vent Damper OperationFlair Damper VENT DAMPER Water Connections & System Piping Gas Supply ConnectionsGas Pressure SettingMax. System Model NoSystem Flow Head ft/WCFeed Expansion Tank Piping Diagrams12” Max Air Vent Air Scoop Diaphragm Valve Pipe Pressure Relief Valve to DrainElectrical Wiring Wiring Diagrams Page Page Fig. 17 Single-ZoneTaco Valve Fig. 18 Dual-ZoneTaco ValveFig. 19 Dual-ZoneHoneywell Valve Fig. 21 Power Vent System with Zone Valve Fig. 20 System with Three 3 Zone PumpsFig. 22 Primary/Secondary Pumping System Honeywell Zone Valve Fig. 24 IID Units with Low Water Cut-offDevice General Location of Controls SERVICING PROCEDURESSEQUENCE OF OPERATION Intermittent Ignition Device IIDFor Standing Pilot Models START-UP PROCEDURESLighting the Boiler Filling the SystemFor Automatic Ignition Models ModelsTo Turn Off Gas to the Boiler Models HONEYWELL PILOT5.For Honeywell valve Turn gas control knob Shut-downProcedureTo Turn Off Gas to the Boiler 3.For Honeywell valveFor Standing Pilot Systems Testing the Ignition Safety Shut-offSafe Shut-downTests Limit ActionProcedure for Cleaning Flue Gas Passageways Inspection ProceduresLow Water Cut-OffWhen Installed BurnersHeat Exchanger Removal REPAIR PROCEDURESTube Cleaning Procedure Typical Burner Tray RemovalHeat Exchanger Re-assembly Combustion Chamber RemovalSOLUTIONS TROUBLESHOOTINGPROBLEM CAUSES10Defective ignition module or defective gas valve Flame Roll-outSwitch Replacement Adjustment & Replacement of ComponentsGas Valve Replacement Vent Thermal Switch ReplacementCirculator Replacement Replacement Parts ListFast-ResponseTemperature Sensor Probe Replacement 2-StageController ModelsADDITIONAL WARRANTY EXCLUSIONS LIMITED PARTS WARRANTYHEAT EXCHANGER WARRANTY PARTS REPLACEMENT