MAINTENANCE

Bay Glass Removal

TO REMOVE FAN:

1)Remove the door from the unit and place on a soft surface to prevent scratching.

2)Remove the nuts holding the glass retainers in place.

3)Remove the glass retainers (sides, top and bottom).

4)Replace the glass. The glass must have gasketing around it.

5)Reverse the previous steps, replace the retainers and fasten with the nuts but do not over tighten, as this can break the glass.

6)Replace door on the stove and check the seal.

1)Turn the unit off and allow it to cool to room temperature.

2)Unplug or disconnect power source to stove.

3)Remove glass front (see page 11).

4)Remove logs and brick panels, if used.

5)Remove the grate by loosening the two screws and sliding the grate out.

6)Remove the burner/front log support as- sembly by removing the 2 screws and lifting it out.

Grate screws

7)Remove the 2 screws holding the Air Intake Hood to the rear firebox wall and lift out.

Replacing fan:

Reverse above steps. Hint for pushing fan down onto pins - rub a bit of dish soap on the grommet so it will slide more easily onto the pin.

FAN MAINTENANCE

If your fan requires maintenance or replace- ment, access to the fan is through the plate on the rear wall of the firebox. NOTE: the unit

MUST NOT be operated without the fan access panel securely in place.

Caution: Label all wires prior to disconnecting when servicing con- trols. Wiring errors can cause im- proper and dangerous operation. Verify proper operation after serv- icing.

8)Remove the 10 screws holding the Access Panel in place.

9)Remove the Fan Air Duct by loosening the 3 screws, squeeze the sides together to remove.

10)Unplug the wires from the fan motor (from inside the stove).

11)Lift Fan Assembly off of the 2 pins, tip forward and pull through firebox opening.

12)Disconnect green wire from power cord.

Check to make sure the fan is seated properly on the pins, this is very important- try to move the fan back and forth, there should be no noise, if there is check that the grommets haven't come loose.

Seal fan access panel using high temperature silicone (sparingly).

U32-3 FPI Direct Vent Gas Insert

25

Page 25
Image 25
Regency U32-NG3 installation manual FAN Maintenance, Grate screws, Replacing fan

U32-NG3 specifications

The Regency U32-NG3 is an innovative and elegant gas fireplace designed to enhance the ambiance of any living space while providing efficient heating. With its sleek design and modern technology, the U32-NG3 is a prime example of Regency's commitment to quality craftsmanship and customer satisfaction.

One of the main features of the U32-NG3 is its clean, contemporary lines that fit seamlessly into both traditional and modern interiors. The fireplace boasts a large viewing area, thanks to its expansive glass front. This design not only provides an unobstructed view of the flames but also allows for greater heat output, making the U32-NG3 an efficient choice for heating.

The U32-NG3 is designed with a direct vent system, which ensures that combustion gases are vented outside the home, promoting a clean indoor environment. This feature also maximizes the efficiency of the fireplace, as it draws air from outside for combustion, reducing heating costs. The direct vent technology is particularly beneficial for homes in colder climates as it minimizes the draw of warm air from the living space.

In terms of heating capacity, the U32-NG3 is powerful, capable of delivering up to 30,000 BTUs. This output is suitable for medium to large rooms, ensuring a cozy atmosphere on cold winter evenings. Homeowners can also customize the flame height and heat output to suit their comfort needs.

Safety is a top priority with the U32-NG3. It includes advanced safety features such as an automatic shut-off system that activates in case of a malfunction or blockage in the venting system. The fireplace also has a safety screen that prevents unintended contact with the flames while allowing for maximum heat circulation.

The U32-NG3 is equipped with state-of-the-art electronic ignition, which ensures quick and reliable startups at the push of a button. Additionally, the fireplace can be operated remotely with a convenient wall switch or optional remote control, adding further ease of use.

In conclusion, the Regency U32-NG3 is a versatile gas fireplace that combines style, efficiency, and advanced technology. Its focus on safety, ease of use, and impressive heating capabilities make it an ideal choice for homeowners looking to upgrade their living space with a modern heating solution. With the U32-NG3, you can create a warm and inviting atmosphere while enjoying all the benefits of a high-quality gas fireplace.