Key Switch | RIDGID TS 2400 specification

b. To turn saw OFF, PUSH lever in. Never leave the saw until the cutting tool has come to a complete stop.

c. To lock switch in OFF position, hold switch IN with one hand, REMOVE key with other hand.

WARNING: For your own safety, lower blade or other cutting tool below table surface. (If blade is tilted, return it to vertical, 90°, position.) Always lock the switch “OFF”. When saw is not in use, remove key and keep it in a safe place. Also, in the event of a power failure (all of your lights go out) turn switch off, lock it and remove the key. This will prevent the saw from start- ing up again when the power comes back on.

13.Thermal Overload Device...opens the power line circuit when the motor temperature exceeds a safe level, when the motor is overloaded or when a lower voltage condition exists. It can be reset by pressing the reset button after the motor returns to nor- mal temperate.

14.Table...provides working surface to support workpieces.

15.Miter Gauge...head is locked in position for cross cutting or mitering by tightening the lock knob. Always securely lock it when in use.

a.There are adjustable screw stops for the stop pin 0° and 45° right and left positions for conveniently setting the miter gauge to cut miters at these standard angles.

Key

Switch

16.Blade Guard

Use the sawblade guard, spreader and anti-kickback pawls for any thru- sawing (whenever the blade comes through the top of the workpiece). Make sure the anti-kickback pawls work properly. Make sure the spreader is in line with sawblade. (See “Aligning Blade Guard” section) To remove the guard for special operations, loosen the blade guard locking knob. Do not disturb the set- ting of the spreader bracket.

When replacing the guard, position the two (2) locator pins on the blade guard into the matching holes in the cradle. Securely tighten the blade guard locking knob.

17

Image 17

RIDGID TS 2400 manual Key Switch, Table...provides working surface to support workpieces

Contents

Page Table of Contents Before Using The Saw Safety Instructions For Table Saw Inspect your saw Reduce the Risk of Dangerous EnvironmentTo reduce the risk of injury from unexpected saw movement Inspect your work area Inspect Your Blade Dress for safety Safety Instructions For Table SawsPlan your work Inspect your workpiece Keep Children Away Reduce the Risk of Accidental StartingDon’t Force Tool Before freeing jammed material To remove loose pieces beneath or trapped inside the guard To reduce the risk of throwback of cut off piecesBefore Leaving The Saw Before Starting While Cutting Glossary of Terms for Woodworking Push Block Push StickRabbet Resin Motor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Thermal Overload Protector Wire SizesThermal Overload Device Extension Gauge Cord Length Unpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key Switch Sawdust Ejection Port Rip Fence Storage Wrench/Blade StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Tools Needed AlignmentRemove Foam Motor Support Checking Table Insert Marked ToothSawblade To check for parallelismCombination Miter Gauge Square Groove Alignment To Check For Squareness, 90 Position Checking Blade Tilt, or Squareness of Blade to TableIf blade is square to table Square Blade Pointer at Position Stopscrew Scale Screws Stopscrew To check for alignment, 45 PositionIf blade is 45 to table Pages Rip Scale Hold Down Adjusting Rip Fence Guide BarsAligning Rip Fence Guide Bars Combination Square Rip Fence Alignment AdjustmentAligning Sliding Table Extension Adjusting Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Nut Rip Indicator If the sliding table extension moves when locked Installing Blade GuardChecking Sliding Table Extension Hex Locking Front Hex Nut Coupling Wood Aligning Blade GuardKerf Spreader Blade Do not loosen other screws. This Removing and Installing Sawblade Miter Gauge Alignment Marking Ind-I-Cut Using Adjusting Bevel LockMarking the Ind-I-Cut Blade Tilt Lock Nut Table Saw Mounting Procedures Workbench Mounting Using HardwareFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your Saw Supporting Table Saw with Sawhorses Workbench Mounting Using C Clamps Before Each Use Inspect your saw Safety Instructions for Basic Saw Operations Plan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push Stick Auxiliary Fence Fence Facing Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations Crosscutting Clamp Wood Block Cut Off Piece Repetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting While Thru sawing Using the Rip FenceAdditional Safety Instructions for Rip Cuts Blade Path RippingOnce the trailing end is on the table Push Block Workpiece Auxiliary Fence Baffle Bevel Ripping Narrow WorkAuxiliary Fence Clamp Might otherwise pinch the blade Using Featherboards for Thru SawingKerf and cause a kickback Push Using Featherboards for Non-Thru Sawing Using Carbide Tipped Blades Install blade guard immediatelyResawing Kickback Dado InsertSaw Arbor Dadoing Ploughing and Molding Rabbeting Molding Auxiliary Fence Molding Maintaining Your Table Saw MaintenanceAdjusting Nylon Set Screw Replacing Carbon Brushes Ridgid Recommends the Following AccessoriesLubrication SKU No Trouble Probable Cause Remedy TroubleshootingGeneral Trouble Probable Cause Remedy Motor Parts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair Parts Key Description Always Order by Part Number not by Key Number Repair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001 Always Order by Part Number Not by Key Number Description Miter Gauge Assembly Fence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC