Checking Sliding Table Extension | RIDGID TS 2400 specs

Alignment (continued)

Checking Sliding Table Extension

Lock the table extension lock lever. Pull- push on the sliding table extension. It should not move.

WARNING: To reduce the risk of thrown workpiece, do not use with extension lock lever unlocked.

If the sliding table extension moves when locked:

1.Release the table extension lock lever.

2.Find the front hex coupling located underneath the front table.

3.Loosen the hex locking nut.

4.Turn the hex coupling counterclock- wise.

5.Lock the table extension lock. Pull-push on the sliding table extension. Readjust hex coupling if necessary. Tighten the hex locking nut against coupling.

Hex Locking	Front Hex
Nut	Coupling

Installing Blade Guard

1.Locate the blade guard.

2.Two (2) locator pins are on the blade guard. These locator pins fit into match- ing holes on a bracket located on the table saw trunnion.

3.Turn the blade guard locking knob clockwise to securely attach the blade guard in place.

Pin

Blade Guard

Locking Knob

28

Image 28

RIDGID TS 2400 Checking Sliding Table Extension, Installing Blade Guard, If the sliding table extension moves when locked

Contents

Page Table of Contents Safety Instructions For Table Saw Before Using The Saw To reduce the risk of injury from unexpected saw movement Reduce the Risk of Dangerous EnvironmentInspect your saw Inspect Your Blade Inspect your work area Safety Instructions For Table Saws Dress for safetyPlan your work Inspect your workpiece Reduce the Risk of Accidental Starting Keep Children AwayDon’t Force Tool Before freeing jammed material To reduce the risk of throwback of cut off pieces To remove loose pieces beneath or trapped inside the guardBefore Leaving The Saw Before Starting Glossary of Terms for Woodworking While Cutting Push Stick Push BlockRabbet Resin Motor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Wire Sizes Thermal Overload ProtectorThermal Overload Device Extension Gauge Cord Length Unpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Key Switch Table...provides working surface to support workpieces Sawdust Ejection Port Wrench/Blade Storage Rip Fence StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Alignment Tools NeededRemove Foam Motor Support Checking Table Insert To check for parallelism Marked ToothSawbladeCombination Miter Gauge Square Groove Alignment Checking Blade Tilt, or Squareness of Blade to Table To Check For Squareness, 90 PositionIf blade is square to table Square Blade Pointer at Position Stopscrew If blade is 45 to table To check for alignment, 45 PositionScale Screws Stopscrew Aligning Rip Fence Guide Bars Adjusting Rip Fence Guide BarsPages Rip Scale Hold Down Aligning Sliding Table Extension Rip Fence Alignment AdjustmentCombination Square Rip Fence Lock Lever Adjustment Adjusting Rip IndicatorAdjusting Nut Rip Indicator Installing Blade Guard If the sliding table extension moves when lockedChecking Sliding Table Extension Hex Locking Front Hex Nut Coupling Aligning Blade Guard WoodKerf Spreader Blade Do not loosen other screws. This Removing and Installing Sawblade Miter Gauge Alignment Adjusting Bevel Lock Marking Ind-I-Cut UsingMarking the Ind-I-Cut Blade Tilt Lock Nut Workbench Mounting Using Hardware Table Saw Mounting ProceduresFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your Saw Workbench Mounting Using C Clamps Supporting Table Saw with Sawhorses Safety Instructions for Basic Saw Operations Before Each Use Inspect your saw Plan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Stick Push Block For Use with Auxiliary Fence Auxiliary Fence Fence Facing Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations Crosscutting Repetitive Crosscutting Clamp Wood Block Cut Off Piece Bevel Crosscutting Miter CrosscuttingCompound Crosscutting Additional Safety Instructions for Rip Cuts Using the Rip FenceWhile Thru sawing Once the trailing end is on the table RippingBlade Path Auxiliary Fence Clamp Bevel Ripping Narrow WorkPush Block Workpiece Auxiliary Fence Baffle Using Featherboards for Thru Sawing Might otherwise pinch the bladeKerf and cause a kickback Push Using Featherboards for Non-Thru Sawing Install blade guard immediately Using Carbide Tipped BladesResawing Kickback Dadoing Dado InsertSaw Arbor Rabbeting Ploughing and Molding Molding Molding Auxiliary Fence Adjusting Nylon Set Screw MaintenanceMaintaining Your Table Saw Ridgid Recommends the Following Accessories Replacing Carbon BrushesLubrication SKU No General TroubleshootingTrouble Probable Cause Remedy Motor Trouble Probable Cause Remedy Repair Parts Parts List for Ridgid 10 Inch Table Saw Model No. TS24001 Always Order by Part Number not by Key Number Key Description Repair Parts Parts List for Ridgid 10 Inch Table Saw Model TS24001 Key Description 827483 Cover Blade Miter Gauge Assembly Always Order by Part Number Not by Key Number Description Fence Assembly Guard Assembly Page Page Page RIDGID, INC Stock No. TS2400 Model No. TS24001 Serial No