To check for parallelism, Marked ToothSawblade | RIDGID TS 2400

Checking Heeling Adjustment or Parallelism of Sawblade to Miter Gauge Groove

While cutting, the material must move in a straight line parallel to the sawblade. Therefore, both the miter gauge groove and the rip fence must be parallel to the sawblade.

WARNING: The blade must be parallel to the miter gauge groove. Misaligned blades could bind on workpiece. Workpiece could suddenly kickback. You could be cut or hit.

Marked

ToothSawblade

x

If the sawblade is not parallel to the miter

Combination

Miter Gauge

gauge groove, the blade will bind at one end of the cut. This is known as “Heeling”.

WARNING: To reduce the risk of injury from accidental start, make sure switch is “OFF” and plug is not connected to power source outlet.

To check for parallelism:

Square

Groove

1.Raise blade all the way up.

2.Mark an “X” on one of the teeth which is set (bent) to the right.

3.Place the head of a combination square in the groove. Adjust blade of square so that it just touches the tip of the marked tooth.

4.Move square to rear, rotate blade to see if marked tooth again touches blade of square.

5.If tooth touches square the same amount at front and rear, sawblade is parallel to miter gauge groove.

6.If tooth does not touch the same amount, the mechanism underneath must be adjusted to make the blade parallel to groove.

WARNING: To reduce the risk of injury from accidental start, make sure switch is “OFF” and plug is not connected to power source outlet.

Alignment

Screws

21

Image 21

RIDGID TS 2400 To check for parallelism, Marked ToothSawblade, Combination Miter Gauge, Square Groove, Alignment Screws

Contents

Page Table of Contents Before Using The Saw Safety Instructions For Table Saw Reduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect your saw Inspect your work area Inspect Your Blade Dress for safety Safety Instructions For Table SawsPlan your work Inspect your workpiece Keep Children Away Reduce the Risk of Accidental StartingDon’t Force Tool Before freeing jammed material To remove loose pieces beneath or trapped inside the guard To reduce the risk of throwback of cut off piecesBefore Leaving The Saw Before Starting While Cutting Glossary of Terms for Woodworking Push Block Push StickRabbet Resin Motor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Thermal Overload Protector Wire SizesThermal Overload Device Extension Gauge Cord Length Unpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key Switch Sawdust Ejection Port Rip Fence Storage Wrench/Blade StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Tools Needed AlignmentRemove Foam Motor Support Checking Table Insert Marked ToothSawblade To check for parallelismCombination Miter Gauge Square Groove Alignment To Check For Squareness, 90 Position Checking Blade Tilt, or Squareness of Blade to TableIf blade is square to table Square Blade Pointer at Position Stopscrew To check for alignment, 45 Position If blade is 45 to tableScale Screws Stopscrew Adjusting Rip Fence Guide Bars Aligning Rip Fence Guide BarsPages Rip Scale Hold Down Rip Fence Alignment Adjustment Aligning Sliding Table ExtensionCombination Square Adjusting Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Nut Rip Indicator If the sliding table extension moves when locked Installing Blade GuardChecking Sliding Table Extension Hex Locking Front Hex Nut Coupling Wood Aligning Blade GuardKerf Spreader Blade Do not loosen other screws. This Removing and Installing Sawblade Miter Gauge Alignment Marking Ind-I-Cut Using Adjusting Bevel LockMarking the Ind-I-Cut Blade Tilt Lock Nut Table Saw Mounting Procedures Workbench Mounting Using HardwareFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your Saw Supporting Table Saw with Sawhorses Workbench Mounting Using C Clamps Before Each Use Inspect your saw Safety Instructions for Basic Saw Operations Plan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push Stick Auxiliary Fence Fence Facing Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations Crosscutting Clamp Wood Block Cut Off Piece Repetitive Crosscutting Miter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsWhile Thru sawing Ripping Once the trailing end is on the tableBlade Path Bevel Ripping Narrow Work Auxiliary Fence ClampPush Block Workpiece Auxiliary Fence Baffle Might otherwise pinch the blade Using Featherboards for Thru SawingKerf and cause a kickback Push Using Featherboards for Non-Thru Sawing Using Carbide Tipped Blades Install blade guard immediatelyResawing Kickback Dado InsertSaw Arbor Dadoing Ploughing and Molding Rabbeting Molding Auxiliary Fence Molding Maintenance Adjusting Nylon Set ScrewMaintaining Your Table Saw Replacing Carbon Brushes Ridgid Recommends the Following AccessoriesLubrication SKU No Troubleshooting GeneralTrouble Probable Cause Remedy Trouble Probable Cause Remedy Motor Parts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair Parts Key Description Always Order by Part Number not by Key Number Repair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001 Always Order by Part Number Not by Key Number Description Miter Gauge Assembly Fence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC