Speaker Connections 
Turn off all the components in the system before connecting the speakers. The RA-1062 has color-coded speaker connectors on the back panel. These connectors accept bare wire, or connector lugs. (In non-EC markets, the con- nectors also accept dual banana plugs.)
Route the wire from the RA-1062 to the speakers. Give yourself enough slack so you can move the components to allow access to the speaker connectors. If you are using dual banana plugs, connect them to the wires and then plug into the backs of the binding posts. The thumbscrews of the binding posts should be screwed in all the way (clockwise).
If you are using terminal lugs, connect them to the wires. If you are attaching bare wires directly to the binding posts, separate the wire conductors and strip the insulation from the end of each conductor. Be careful not to cut into the wire strands. Unscrew (turn counterclockwise) the binding post thumbscrews. Place the connec- tor lug or wire around the binding post shaft. Turn the thumbscrews clockwise to clamp the connector lug or wire firmly in place.
NOTE: Be sure there are no loose wire strands that could touch adjacent wires or connectors.
Signal Connections
See Figure 3
The RA-1062 has line level inputs for source components, connections for audio tape decks, and preamp output connections to send signals to an external power amplifier.
NOTE: To prevent loud, potentially damag- ing, noises, make sure the system is turned off when you make any signal connections.
Phono Input 
and
Ground Connection 
Plug the cable from the turntable into the ap- propriate left and right phono inputs. If the turntable has a “ground” wire connect it to the screw terminal to the left of the Phono inputs. It will help prevent hum and noise.
7
Line Level Inputs 
The RA-1062 has three pair of conventional RCA input connectors for line level components such as CD players, video cassette recorders, tuners, Laser Disc players, or DVD players. These inputs are labeled CD, TUNER, AUX.
The left and right channels are clearly labeled and should be connected to the corresponding channels of the source component. The left RCA connectors are white, the right connectors are red. Use high quality RCA cables for connect- ing input source components to the RA-1062. Ask your authorized Rotel dealer for advice about cables.
Recorder Connections 
Tape inputs and outputs can be connected to any record/playback device that accepts standard line level analog input and output signals. Typically that will be a conventional tape recorder. There are two sets of tape con- nections on the back panel, labelled TAPE 1 and TAPE 2.
When connecting a recorder to the RA-1062, the outputs of the recorder must be connected to the tape inputs of the RA-1062. Similarly the tape outputs of the RA-1062 must be con- nected to the inputs of the recorder. Be sure to connect the left and right channels of each device to the proper channels on the associ- ated components. Use high quality connecting cables to prevent loss of sound quality.
NOTE: The tape inputs can also be used for standard playback-only source components, omitting the output connections.
Preamp Outputs 
The RA-1062 has a pair of preamp outputs that can send a variable gain signal to an external power amp or signal processor. The preamp outputs are standard RCA-type output connectors, compatible with the inputs of most power amplifiers. Use high quality cables and be sure to connect the left and right channel outputs of the RA-1062 to the correct channels of the amplifier.
English
AC Power and Control
AC Power Input 
Because of its relatively high power rating, the RA-1062 can draw considerable current. Therefore, it should be plugged directly into a 2- pin polarized wall outlet. Do not use an extension cord. A heavy duty multi-tap power outlet strip may be used if it (and the wall outlet) is rated to handle the current demanded by the RA-1062 and all the other components connected to it.
Your RA-1062 is configured at the factory for the proper AC line voltage in the country where you purchased it (USA: 115 volts/60Hz AC or CE: 230 volts/50 Hz AC). The AC line configuration is noted on a decal on the back panel. Plug the supplied cord into the AC INPUT receptacle on the back of the unit.
NOTE: Should you move your RA-1062 to another country, it is possible to recon- figure your amplifier for use on a different line voltage. Do not attempt to perform this conversion yourself. Opening the enclosure of the RA-1062 exposes you to dangerous voltages. Consult a qualified service person or the Rotel factory service department for information.
If you are going to be away from home for an extended period of time such as a month long vacation, it is a sensible precaution to unplug your audio and video components while you are away.
POWER Button 
Power Indicator 
Press the front panel POWER button, to turn the RA-1062 on. The power indicator light is illumi- nated when the RA-1062 is on. Press POWER button again to turn the RA-1062 off.
Once the RA-1062 has been turned on with the front panel button, it can be switched between normal operating mode and standby mode with the POWER button on the RR-AT94 remote control.
