Rotel RC-1082 AC Power and Control, Input Signal Connections e and r, RR-AT97Remote Control

RC-1082Stereo Control Amplifier

Placement

Like all audio components that handle low-level signals, the RC-1082 can be affected by its environment. Do not stack the RC-1082 on top of a power amplifier. This will minimize chance it will pick up hum or interference. We recommend installing the RC-1082 in furniture designed to house audio components. Such furniture is designed to reduce or suppress vibration which can adversely affect sound quality. Ask your authorized Rotel dealer for advice about component furniture and proper installation of audio components.

Cables

Be sure to keep the power cords, digital signal cables and regular audio signal cables in your installation away from each other. This will minimize the chance of the regular audio signal cables picking up noise or interference from the power cords or digital cables. Using only high quality, shielded cables will also help to prevent noise or interference from degrad- ing the sound quality of your system. If you have any questions see your authorized Rotel dealer for advice about the best cable to use with your system

RR-AT97 Remote Control

The RC-1082 includes a full-function remote control that performs most of the functions of the front panel controls. In addition it can operate many of the controls on other Rotel components. See the “Controlling Other Components” section of this manual for more information.

Most of the RR-AT97 functions duplicate the front panel controls. In this manual the remote control functions are covered in the same section as the front panel control operation. Numbers in gray boxes such as 1 indicate items on the front and rear panel control and connection illustrations. See Figure 1 on page

3.Letters in gray circles such as A indicate items on the RR-AT97 illustration. See Figure 2 on page 3.

6

Remote Sensor 3

The Remote Sensor is located to the right of the Phones jack on the front panel. It picks up the infrared signals from the remote control. Do not cover or block the sensor. It must be clear of obstructions or the remote control will not work properly. The operation of the Remote Sensor can also be affected if it is exposed to bright light, particularly sun light. In addition remote control functions may not work reliably if the batteries in the RR-AT97 are weak.

AC Power and Control

AC Power Input [

NOTE: The RC-1082 will be turned on and in the normal operating mode as soon as it is connected to the AC outlet. Be sure to set the Volume control to the minimum (full counterclockwise) position before connect- ing the power cord.

Connect the supplied power cord to the AC Input receptacle on the rear panel. Do not connect the power cord to the power outlet until all the audio input and output connections have been made.

It is usually best to plug the RC-1082 directly into a 2-pin polarized wall outlet. Avoid the use of extension cords. A heavy duty multi-tap power outlet strip may be used if it (and the wall outlet) is rated to handle the current demanded by the components connected to it.

Your RC-1082 is configured at the factory for the proper AC line voltage in the country where you purchased it (either 120 volts AC or 230 volts AC with a line frequency of either 50 Hz or 60 Hz). The AC line configuration is noted on a decal on the rear panel.

NOTE: Should you move your RC-1082 amplifier to another country, it is possible to reconfigure your amplifier for use on a dif- ferent line voltage. Do not attempt to per- form this conversion yourself. Opening the enclosure of the RC-1082 exposes you to dangerous voltages. Consult a qualified ser- vice person or the Rotel factory service de- partment for information.

If you are going to be away from home for an extended period of time such as a month-long vacation, it is a sensible precaution to unplug your amplifier (as well as other audio and video components) while you are away.

STANDBY Switch 1

Remote OFF/ON Switch A

STANDBY Indicator 2

The STANDBY switch 1is located on the left side of the front panel. When the RC-1082 is first plugged into a power outlet it will be in “operation” mode and the Standby indicator 2 will be lit.

In addition the indicators above the selected Listening and Recording input buttons 90 will light. Press the front panel Standby switch again, or the “Off” button on the remote, to return the RC-1082 to “standby” mode.

NOTE: The RC-1082 will be turned on and in the normal operating mode as soon as it is connected to the AC outlet. Be sure to set the Volume control to the minimum (full counterclockwise) position before connect- ing the power cord.

Input Signal Connections e and r

[See Figure 3.]

The RC-1082 has conventional RCA-type connectors for all inputs.

NOTE: To prevent loud noises that neither you nor your speakers will appreciate, make sure the system is turned off when you make any signal connections.

Line Level Inputs r

The CD, Tuner, and Aux inputs of the RC-1082 are “line level” inputs. These are for connecting the analog outputs from components such as CD players, DVD players, video disc recorders, tuners for audio or video, or VCRs.

The Left and Right channels are clearly labeled and should be connected to the corresponding channels of the source component. The Left RCA connectors are white, the Right connec- tors are red. Use high quality RCA cables for connecting input source components to the RC-1082. Ask your authorized Rotel dealer for advice about cables.