|
| 9 | English |
|
|
|
|
NOTE: By default, the |
|
| |
the Rotel |
|
| |
The remote can be reprogrammed to oper- |
|
| |
ate the |
|
| |
only needs to be done once: |
|
| |
To program for the |
|
| |
the ON button and the 2 button simultane- |
|
| |
ously. |
|
| |
To program for the |
|
| |
|
| ||
and the 1 button simultaneously. |
|
| |
|
|
|
|
Troubleshooting |
|
| |
Most difficulties in audio systems are the result |
|
| |
of incorrect connections, or improper control |
|
| |
settings. If you encounter problems, isolate the |
|
| |
area of the difficulty, check the control settings, |
|
| |
determine the cause of the fault and make the |
|
| |
necessary changes. If you are unable to get |
|
| |
sound from the |
|
| |
tions for the following conditions: |
|
| |
Standby Power Indicator Is |
|
| |
Not Lit |
|
| |
The Standby Power Indicator should be lit |
|
| |
whenever the |
|
| |
wall power outlet. If it does not light, test the |
|
| |
power outlet with another electrical device, |
|
| |
such as a lamp. Be sure the power outlet be- |
|
| |
ing used is not controlled by a switch that has |
|
| |
been turned off. | Specifications |
| |
Fuse Replacement |
| ||
If another electrical device works when plugged |
|
| |
into the power outlet, and the Standby Indicator | Total Harmonic Distortion | < 0.004% | |
still will not light when the | Intermodulation Distortion (60 Hz : 7 kHz, 4:1) | < 0.004% at 1V output | |
into the wall outlet, it indicates that the internal | Input Sensitivity / Impedance |
| |
power fuse may have blown. If you believe this | Phono - MC | 250 µV / 100 ohms | |
has happened, contact your authorized Rotel | Phono - MM | 2.5 mV / 47 kOhms | |
dealer to get the fuse replaced. | Line Level | 150 mV / 220 kOhms | |
No Sound | Phono Overload (MC/MM) | 16 mV / 160 mV | |
Output Sensitivity / Impedance | 1 V/ 100 Ohms | ||
Check the signal source to see if it is functioning | Frequency Response |
| |
properly. Make sure the cables from the signal | Phono Input | ||
source to the | Line Level Input | ||
properly. Be sure the Listening Selector is set | Signal to Noise Ratio (IHF “A” weighted) |
| |
to the proper input. Check the power ampli- | Phono - MC/MM | 70 dB/75 dB | |
fier for power and proper operation. Check | Line Level | 100 dB | |
all the wiring between the | Power Requirements |
| |
power amplifier, and the power amplifier | USA Version | 120 Volts, 60 Hz | |
and speakers. | European Version | 230 Volt, 50 Hz | |
|
| Power Consumption | 15 Watts |
|
| Standby Power Consumption | 2.5 Watts |
|
| Dimensions (W x H x D) | 432 x 92 x 344 mm |
|
|
| 17 x 3 5/8 x 13 9/16” |
|
| Weight (net) | 7.5 kg, 16.53 lbs. |
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.