Rotel RSP-1069 Con guring Speakers and Audio

English

This conﬁ guration may not be ideal for mul-

tichannel systems conﬁ gured with high-pass

speakers, redirecting bass to a powered

subwoofer. An option, called LFE REDIRECT,

sends the seven main channels directly to

the outputs as usual. In addition, it takes

a duplicate copy of these seven channels,

combines them into mono, and routes them

through a 100 Hz analog low-pass cross-

over to the subwoofer preamp output. This

creates a summed mono subwoofer signal,

derived from the seven main channels of the

MULTI INPUT.

Use the LFE REDIRECT off for the pure ana-

log bypass conﬁ guration. Use the LFE REDI-

RECT on setting to derive the mono summed

subwoofer output.

Dolby Pro Logic IIx

9DA7NEGDAD<>8>>m



BD9:/Bjh^X



DEI>DC6AE6G6B:I:GH

E6CDG6B6/D[[

9>B:CH>DC/(

8:CI:GL>9I=/%



>CEJIH:IJEB:CJ



When Dolby Pro Logic IIx is selected as the

default surround mode on the INPUT SETUP

menu, there are additional settings and pa-

rameters to optimize the surround decoding

for music or movie soundtracks. Dolby Pro

Logic II uses matrix decoding algorithms to

derive a center channel and surround chan-

nels from 2-channel source material.

The ﬁ rst line of the Dolby Pro Logic IIx sub-

menu selects CINEMA, MUSIC, GAME, or

PRO LOGIC modes for matrix decoding.

Use the +/– buttons on the remote to select

a mode.

Select CINEMA to optimize for Dolby Sur-

round encoded movie soundtracks includ-

ing increased surround separation and full-

bandwidth surround channel frequency re-

sponse.

Select MUSIC to optimize for musical record-

ings. When the MUSIC mode is selected, three

additional parameters will be available on

the OSD screen. Use the UP/DOWN buttons

on the remote to select a parameter. Use the

+/– buttons to change the selected param-

eter as follows:

• PANORAMA: The Panorama option ex-

tends the front stereo image to include the

surround speakers for a dramatic “wrap-

around” effect. The options are OFF or

ON.

• DIMENSION: The Dimension option al-

lows you to gradually adjust the sound-

ﬁ eld towards the front or towards the rear.

There are seven incremental settings from

0 to 6. A setting of 0 shifts the soundﬁ eld

towards the rear for maximum surround ef-

fect. A setting of 6 shifts the soundﬁ eld to

the front for minimum surround effect. The

default setting of 3 provides a “neutral”

balance between the two extremes.

• CENTER WIDTH: The Center Width op-

tion allows you to spread the signal in-

tended for the center speaker to the left

and right front speakers, widening the

perceived soundﬁ eld. There are eight in-

cremental settings from 0 to 7. With the

default setting of 0, there is no center width

spreading and all of the center channel

information is sent to the center speaker.

The maximum setting of 7 shifts all of the

center channel signal to the left and right

speakers, essentially muting the center

speaker and maximizing the soundﬁ eld

width. Other settings provide incremental

steps between the two extremes.

Select GAME to optimize for Dolby Surround

encoded video games.

Select PRO LOGIC for original Dolby Pro

Logic decoding. Typically, Pro Logic II (Cin-

ema or Music modes) will provide better sur-

round performance, even with older source

material. Original Pro Logic mode provides

5.1 channel surround sound, even on 6.1/7.1

channel systems.

When you have completed all the desired ad-

justments, highlight the INPUT SETUP MENU

line at the bottom of the screen and press the

ENTER button to return to the INPUT SETUP

menu (or just press the ENTER button).

DTS Neo:6

9IHCZd/+



BD9:/8^cZbV











>CEJIH:IJEB:CJ



When DTS Neo:6 is selected as the default

surround mode on the INPUT SETUP menu,

there are additional option settings and pa-

rameters available to optimize the surround

decoding for various types of recordings,

music or movie soundtracks. DTS Neo:6

uses matrix decoding algorithms to derive a

center channel and surround channels from

2-channel source material.

In DTS Neo:6 mode, there will only be one

choice available on the sub-menu: selecting

CINEMA or MUSIC modes. Use the +/– but-

tons on the remote to change the settings.

• Select CINEMA to optimize the DTS Neo:6

decoding for movie soundtracks.

• Select MUSIC to optimize the DTS Neo:6

decoding for musical recordings.

When you have completed the setting, high-

light the INPUT SETUP MENU line at the bot-

tom of the screen and press the ENTER but-

ton to return to the INPUT SETUP menu (or

just press the ENTER button).

Conﬁ guring

Speakers and Audio

This section of the setup process covers items

concerning audio reproduction such as the

number of speakers, bass management in-

cluding subwoofer crossovers, establishing

equal output levels for all channels, delay

settings, and tone contour settings.

Understanding Speaker

Conﬁ guration

Home theater systems vary in the number of

speakers and the bass capabilities of those

speakers. The RSP-1069 offers surround modes

tailored to systems with various numbers of

speakers and bass management features which

send bass information to the speaker(s) best

able to handle it – subwoofers and/or large