Rotel RSP-1069 Advance Speaker Setup

English

CENTER BACK SPEAKER(S) (large1/

large2/small1/small2/none): Some sys-

tems have one or two additional center back

surround speakers. Select the LARGE settings

(not available with SMALL front speakers) to

have your center back speaker(s) play low

bass. Use LARGE 1 if you have one center

back speaker (6.1) or LARGE 2 (7.1) if you

have two center back speakers (7.1). If your

center back speakers have limited bass ca-

pability or if you would prefer that the bass

go to a subwoofer, use the SMALL setting

(SMALL1 for one speaker, SMALL2 for two

speakers). If your system has no center back

speakers, select the NONE setting. With

center back speakers, the Rotel XS eXtended

surround, Dolby Digital EX, DTS-ES, Dolby

Pro Logic II, DTS Neo:6 or other decoders

will provide center back signals for any sur-

round mode.

SUBWOOFER (yes/no/max): The YES set-

ting is the standard setting if your system has

a subwoofer. If your system does not have a

subwoofer, select NO. Select the MAX setting

for maximum bass output with normal bass

being duplicated by both the subwoofer and

any LARGE speakers in the system.

ADVANCED: Speaker conﬁ guration is gen-

erally a global setting for all surround modes

and need only be done once. However, for

special circumstances, the RSP-1069 provides

the option of setting the speaker conﬁ gura-

tion independently for each of four surround

modes. Select the ADVANCED line on the

menu and press ENTER to go to the AD-

VANCED SPEAKER SETUP menu described

in the following section.

To change a setting on the SPEAKER SETUP

menu, place the highlight on the desired line

using the UP/DOWN buttons and use the

+/– buttons to toggle through the available

settings. To return to the MAIN menu, press

the ENTER button. Press the MENU/OSD but-

ton on the remote to cancel the display and

return to normal operation.

Advance Speaker Setup

69KHE:6@:GH:IJE



HE:6@:G/;gdci

8GDHHDK:G/&%%=o



9DA7N/HbVaa

9IH/HbVaa

HI:G:D/AVg\Z

9HE/HbVaa



HE:6@:GH:IJEB:CJ

In most cases, the standard speaker conﬁ g-

uration described above is a global setting

and can be used for all surround modes.

However, the RSP-1069 provides the capa-

bility to customize these settings for four dif-

ferent surround modes: Dolby, DTS, Stereo,

and Music. For example, you could set up

the Dolby and DTS modes for 5.1 channel

sound, while the Stereo mode changes to a

2-speaker setup with or without a subwoofer.

In addition, the ADVANCED SPEAKER SETUP

allows you to select a customized high-pass

crossover frequency for the front, center, sur-

round, and surround back speakers.

NOTE: In most systems, the default settings on

this menu will provide the most predictable

results and most users will not need to change

any settings. You should fully understand bass

management and have a speciﬁ c reason for

needing a custom conﬁ guration before chang-

ing these settings. Otherwise, skip to the fol-

lowing topic, SUBWOOFER SETUP.

The available settings on the ADVANCED

SPEAKER SETUP menu are as follows:

SPEAKER (front/center/surround/

center back/subwoofer): Select the

set of speakers to be conﬁ gured with cus-

tom settings.

CROSSOVER (40Hz/60Hz/80Hz/

100Hz/120Hz/150Hz/200Hz): Typi-

cally, the RSP-1069 uses a single master set-

ting for the high-pass and low-pass cross-

over point between all SMALL speakers and

the subwoofer. This master crossover point

is set on the SUBWOOFER SETUP menu

described in the following section. When

you ﬁ rst access the ADVANCED SPEAKER

SETUP menu, the current master crossover

point will be shown on this line. Change the

value of this line only if you want the current

speaker to have a different crossover point.

For example, if your master crossover is set

to 80Hz, but you want your front speakers

to crossover to the subwoofer at 60 Hz, you

would select 60Hz for the front speakers on

this line. This setting ONLY affects redirected

bass and does not affect the LFE channel in

any way. The OFF setting (available only for

the subwoofer) sends a full-range signal to

your subwoofer so that you can use its built-

in low-pass ﬁ lter.

NOTE: When a speaker is set to LARGE on

the SPEAKER SETUP menu or on this MENU,

the crossover setting is not available since, by

deﬁ nition, a LARGE speaker plays full-range

with no bass redirection to the subwoofer and

no crossover. Likewise, the OFF setting for

the subwoofer crossover is not available for

SMALL speakers, since SMALL means that the

speaker will redirect its bass below a given

crossover point to the subwoofer. In addition,

the CROSSOVER setting is not available for

the MULTI INPUT.

DOLBY (large/small/none): Sets the cur-

rent speaker (shown in the ﬁ rst line) to LARGE,

SMALL, or NONE, overriding the master set-

ting from the SPEAKER SETUP menu. This set-

ting will ONLY take effect with Dolby Digital

or Dolby Pro Logic II decoding.

DTS (large/small/none): The same op-

tions described for Dolby above, except these

settings ONLY take effect with DTS and DTS

Neo:6 decoding.

STEREO (large/small/none): The same

options described for Dolby above, except

these settings ONLY take effect in STEREO

surround mode.

DSP (large/small/none): The same op-

tions described for Dolby above, except these

settings ONLY take effect with any of the DSP

surround modes.

NOTE: When the front speakers are set to use

the master crossover frequency on the AD-

VANCED SPEAKER SETUP menu, the surround

mode speciﬁ c “large/small/none” settings are

not available for the other speakers. These

speakers will use the setting determined in

the basic SPEAKER SETUP menu.