47
English
• Component Video output at 720p or 1080i
may not be available if the source signal
includes HDCP copy protection.
• HDMI cables must be 5 meters or less in
length.
OSD menus are not displayed on TV
Monitor.
• In some PAL systems, the menus may not
be displayed unless there is an active
video signal.
Video and Audio do not match.
• Check that the proper video source is se-
lected for each input.
�� Check that the group delay (lip-synch)
setting is not misadjusted.
Clicking or popping sounds when
switching inputs.
• The unit uses relay switching to preserve
maximum sound quality. The mechanical
clicking of the relays is normal.
• During switching, it may take a split sec-
ond for digital signals to be recognized
and properly decoded. Rapid repeated
switching between inputs or settings can
result in clicks or pops from the speak-
ers as the unit attempts to lock on to the
rapidly changing signals. This causes no
harm.
Controls do not operate.
• Make sure that fresh batteries are installed
in the remote.
• Make sure that the IR sensor on the front
panel is not blocked. Aim the remote at
the sensor.
• Make sure the sensor is not receiving strong
IR light (sunlight, halogen lighting, etc.)
• Unplug the unit from the AC outlet, wait 30
seconds, and plug it back in to reset.
No video from Zones 2, 3, or 4
• Check ZONE SETUP confi guration and
zone video input setting as assigned and
make sure that a Composite source is con-
nected.
Specifi cations
Audio
Total Harmonic Distortion
<0.008%
Intermodulation Distortion (60 Hz:7 kHz)
<0.008%
Frequency Response
10 Hz – 120 kHz, ±3dB (analog bypass)
10 Hz – 95 kHz, ±3dB (digital input)
Signal to Noise Ratio (IHF A-weighted)
95dB (analog bypass)
92dB (Dolby Digital, dts) 0dBFs
Input Sensitivity/Impedance
Line Level: 200 mV/100K ohms
Preamp Output Level/Output Impedance
1.0 V / 1K ohms
Contour (LF/HF)
±6dB at 50 Hz/15 kHz
Decodable Digital Input Signals
Dolby Digital, Dolby Digital EX, DTS, DTS-ES,
DTS 96/24, DTS ES 96/24, LPCM (up to 192K),
HDCD, DVD-A (HDMI HD ONLY)
Video
Input Resolutions
480i/576i
480p/576p
720p
1080i
1080p (HDMI only)
Output Resolutions
480i/576i (Composite, S-Video only)
480p/576p
720p
1080i
1080p (HDMI only)
HDMI Input/Output:
Version 1.1
Signal to Noise Ratio
45dB
Input Impedance
75 ohms
Output Impedance
75 ohms
Output Level
1.0 volt
General
Power Consumption:
80 watts
4.7 watts (standby)
Power Requirements (AC)
120 volts, 60Hz (USA version)
230 volts, 50Hz (CE version)
Weight
9.0 Kg/19.8 lb.
Dimensions (W x H x D)
432 x 122 x 341 mm
17.01” x 4.8” x 13.43”
Front Panel Height
(feet removed for rack mount)
109 mm / 4.29”
When sizing openings in custom cabinets, measure the unit
to be installed and/or allow at least 1 mm clearance on all
sides for unit to unit tolerances.
All specifi cations are accurate at the time of printing. Rotel
reserves the right to make improvements without notice.
Rotel and the Rotel HiFi logo are registered trademarks of
The Rotel Co, Ltd., Tokyo, Japan.