Rotel RSP-1069 Zone 24 Setup, Default Setup

English

Select NO for normal operation. Select YES

to go to a special FLASH UPGRADE MODE

that rewrites the operating software from

a computer connected to the back panel

COMPUTER I/O port. This feature should

only be performed by qualiﬁ ed personnel.

We strongly recommend having your Rotel

Dealer perform this upgrade.

NOTE: After performing the software upgrade,

turn off the RSP-1069. Then, turn it back on

to return to normal operation.

Zone 2–4 Setup

ODC:H:IJE

ODC:/ODC:'

HDJG8:/89

K>9:D>CEJI/8dbedh^iZ&

KDAJB:H:IJE/KVg^VWaZ

KDAJB:/+%

IJGCDCKDA/AVhi

B6MKDA/BVm

&'KIG><<:G/&T(TTT

B6>CB:CJ

The ZONE SETUP menu provides settings and

conﬁ guration options related to the operation

of the remote zones. This menu is reached

by highlighting the ZONE line on the MAIN

menu and pressing ENTER.

ZONE: Specifies the zone to configure,

ZONE 2, 3, or 4. Each zone is conﬁ gured

individually.

SOURCE: Speciﬁ es a source for listening in

the selected zone. Options are CD, TUNER,

TAPE, VIDEO 1–5, SOURCE, and OFF. Se-

lecting the SOURCE option links the zone

source to the source selected for the main

zone so that the remote zone will hear the

same source as the main zone. Selecting the

OFF option turns the zone off.

VIDEO INPUT: Speciﬁ es a video source

(Composite Video only) for the selected

zone. The options available are Composite

1, 2 and 3 and OFF. (If SOURCE, above, is

set to OFF, the VIDEO INPUT selection will

not be available.)

VOLUME SETUP: conﬁ gures the remote zone

outputs for VARIABLE or FIXED volume levels.

VARIABLE allows control of the volume settings

in the remote zone from the RSP-1069 front

panel or from a remote control/IR repeater

in the zone. FIXED output disables the volume

control. In this mode, the remote zone level

can be ﬁ xed at the level speciﬁ ed on the next

line, thus optimizing system performance when

sending a ﬁ xed level signal to a preamp or

ampliﬁ er with its own volume adjustment.

VOLUME: In VARIABLE output mode, this

line shows the current volume setting for re-

mote zone. In FIXED output mode, this volume

setting establishes a permanent ﬁ xed output

level for the remote zone.

Move the highlight to the desired line using

the UP/DOWN buttons and use the +/– but-

tons to adjust the volume level. To return to the

MAIN menu, press the ENTER button. Press the

MENU/OSD button on the remote to cancel the

display and return to normal operation.

TURN ON VOL: Speciﬁ es a default volume

level to be used each time the remote zone is

activated. You can select LAST to have the zone

activate with the last previously used volume

setting. Or, you specify a volume from MIN

(full mute) to MAX, in 1dB increments. Note

that this setting cannot exceed the MAX VOL

established in the next line of the menu.

MAX VOL: Speciﬁ es the maximum volume

level for the remote zone. The volume cannot

be adjusted above this level. Settings range

from MIN to MAX, in 1dB increments.

12V TRIGGER: The RSP-1069 has six 12V

trigger outputs (labeled 1–6) that supply a

12V DC signal to turn on Rotel components

and other components as needed. This menu

item turns on speciﬁ c 12V trigger outputs

whenever the indicated zone is activated. The

six 12V Trigger outputs may be assigned to

each Zone and can send a turn-on signal to

remote components whenever the Zones are

activated. For example, Zone 2 could use 12V

Triggers 1, 3 and 6; Zone 3, 12V Triggers 2

and 3; Zone 4, 12V Triggers 5 and 6.

1. Press the +/– buttons on the remote to

change the ﬁ rst position from blank to 1

(activating TRIGGER 1 for that zone).

2. Press the ENT button on the remote to

move to the next position.

3. Repeat until all six positions are set as

desired. A ﬁ nal press of the ENT button

conﬁ rms the selection.

Default Setup

9:;6JAIH:IJE



;68IDGN9:;6JAI/Cd



JH:G9:;6JAI/Cd

H:IJH:G9:;6JAI/Cd

H:IC:LE6HHLDG9/CD

B6>CB:CJ

The DEFAULT SETUP menu provides access

to three functions:

• Restore all features and settings to the

original FACTORY DEFAULT settings.

• Memorize a custom group of settings as

a USER DEFAULT. This requires entering

a password.

• Activate the USER DEFAULT settings.

• Change the password.

To restore the FACTORY DEFAULT set-

tings: Place the highlight on the FACTORY

DEFAULT line using the UP/DOWN buttons

and use the +/– buttons to change the set-

ting to YES. Press the ENTER button to pro-

ceed with resetting the FACTORY DEFAULT

settings. The unit will power off and then on,

with the factory settings restored. To return

to the MAIN menu without resetting the FAC-

TORY DEFAULT settings, change the entry to

NO and press the ENTER button.

NOTE: Resetting to factory default settings

will erase all stored settings including delay

settings, speaker settings, balance settings,

input settings and more. You will lose ALL

system conﬁ guration settings. Be certain that

you wish to do so before resetting the fac-

tory defaults.

To memorize USER DEFAULT settings:

Many of the current conﬁ guration settings

can be stored as a USER DEFAULT, which

can be activated at any time from this menu

screen. To save the current settings as a

USER DEFAULT:

1. Place the highlight on the SET USER DE-

FAULT line using the UP/DOWN buttons

and use the +/– buttons to change the

setting to YES.

2. Press the ENTER button to go to conﬁ rma-

tion screen where a password must be

entered. The default password is 8888.