Other Settings
Temporary Speaker Level
The levels of all channels should be calibrated using the TEST TONE procedure during the initial setup of the RSP-1098. You can make a temporary change in the relative volume of the center, surround, center back, or subwoofer channels using buttons on the remote control or the front panel controls. These temporary adjustments only remain in effect until a dif- ferent input is selected or until the RSP-1098 is turned off.
To adjust speaker levels using the remote:
1.Press a selection button on the remote to select a channel (or pair of channels) for adjust- ment. Press the C button to adjust the CEN- TER channel. Press the S button to adjust the SUBWOOFER channel. Press the R button to adjust the rear SURROUND or CENTER BACK channels (each press of the R button toggles between the SURROUND channels and the CENTER BACK channels). The se- lected speaker and its current setting appear briefly in the display.
2.Use the UP or DOWN buttons on the re- mote to adjust the output level of the se- lected channel(s).
To adjust speaker levels from the front panel.
1.Press the SPEAKER button repeatedly until the desired speaker or group of speakers is displayed.
2.Rotate the FUNCTION knob to change the level of the selected speaker.
NOTE: If no level adjustment is made for 5 seconds, the levels revert to the default cali- brated settings.
As you select a speaker in the above adjust- ments, you may notice an addition choice, “group delay”. See the following for an ex- planation of this feature.
27
Temporary Group Delay
The SPEAKER adjustments (described above) can also be used to make a temporary ad- justment to the group delay or “lip-synch” delay. Group delay delays the overall audio signal (to all speakers) by a specified amount to correct for situations where the video and audio sig- nals are out of synch. This can occur with upconverted digital TV signals or when trying to match a radio broadcast with the video from a sports event. The settings range from 0 to 500 milliseconds in 5 ms increments.
Like the speaker settings, this is a temporary adjustment that overrides the permanent de- fault setting for a video source until a differ- ent input source is selected or the unit is turned off.
To adjust group delay using the re- mote:
1.Press the C button on the remote twice.
2.Use the UP or DOWN buttons on the re- mote to adjust the amount of delay applied to all channels.
To adjust the group delay from the front panel:
1.Press the SPEAKER button repeatedly un- til you reach the GROUP DELAY option.
2.Rotate the FUNCTION control to adjust the amount of delay applied to all channels.
Dynamic Range 
Dolby Digital recordings are capable of wide dynamic range (the difference between the soft- est and loudest sounds). In some cases, this may tax amplifiers and/or speakers. In other cases, you may want to reduce the dynamic range when listening at low volume levels. This is particularly useful in order to keep dialog loud enough to be intelligible while avoiding excessively loud sound effects. Dolby Digital dynamic compensation is a sophisticated fea- ture that allows you to adjust the dynamic range while still preserving fidelity. The actual amount of compression relies on instructions embed- ded in the Dolby Digital recording and var- ies to best suit the specific program content.
English
There are three dynamic range settings avail- able for Dolby Digital recordings:
MAX: full dynamic range
MID: slightly reduced dynamic range, roughly comparable to the signal from a compact disc
MIN: more heavily reduced dynamic range, but still comparable to the signal from a typi- cal VHS Hi-Fi recording.
To adjust dynamic range using the remote:
Press the DYN button repeatedly until the desired setting appears in the OSD/TFT screen. This setting remains in effect for all Dolby Digital program material until it is changed.
To adjust dynamic range from the front panel:
1.While playing a Dolby Digital source, press the MODE button twice
2.Rotate the FUNCTION control to select the dynamic range setting.
NOTE: The dynamic range compensation fea- ture is only available in Dolby Digital mode. The setting is ignored with all other types of recordings.
Contour/Tone Settings 
The contour adjustment (available only the remote control) changes the high or low fre- quency content at the frequency extremes. The settings can be adjusted up or down by a maximum of 6dB. Adjustments to the contour settings are permanent; they remain in effect until they are readjusted.
Changing the high frequency contour (HF) in- creases or decreases the treble. Changing the low frequency contour (LF) increases or de- creases the bass content. The settings are shown on the OSD and/or TFT displays as you ad- just them.
To adjust the contour settings:
1.Press the TONE button on the remote. Ei- ther LF or HF appears in the OSD/TFT displays, depending on which adjustment is currently active. Press the TONE button again to toggle to the other adjustment.
2.Press the UP/DOWN buttons on the remote to increase or decrease the setting. The display will revert to normal operation fol- lowing several seconds of inactivity.
