Runco SC-1 - page 107

Maintenance and Troubleshooting

Runco SC-1 Owner’s Operating Manual 95

PRELIMINARY

Power and Cooling

40 Lamp has shut down due to fan failure.

46 Red DMD heat sink overheated.

47 Green DMD heat sink overheated.

48 Blue DMD heat sink overheated.

49 Prism overheated.

4C Projector shutdown due to critical error.

4D Integrator has overheated.

4E Inadequate lamp air intake rate (interlock)

4F Inadequate air exhaust rate (interlock)

53 Fan 3 has failed (side [rear] intake fan).

54 Fan 4 has failed (side [front] intake fan).

55 Fan 5 has failed (lamp exhaust fan).

56 Fan 6 has failed (LAD fan).

57 Fan 7 has failed (card cage fan).

58 Fan 8 has failed (heat exchanger fan — for liquid cooling system).

TIPM (Image Processor)

60 Boot code CRC failed.

61 Unable to program DigMux PLD.

62 Unable to program Control PLD.

63 Unable to program Bubks PLD.

64 Unrecognized ROM type.

65 Write to flash ROM failed.

66 General TIPM failure.

67 Downloaded code will not fit into ROMs.

68 Communication error with scaler on TIPM.

Built-In Keypad

70 Unable to access EEPROM on the built-in keypad.

71 EEPROM memory re-initialization on the built-in keypad.

Table 5-2. SC-1 Error Codes (continued)

Code Description

Note: To clear a system error, press the EXIT key (on the SC-1 control panel) twice. If necessary,

reset the projector by powering it off, allowing it to cool and powering it on again. Contact your

Runco dealer or Runco technical support if the error persists.

Contents

Main OWNERS OPERATING MANUAL SC-1 Page TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Page RUNCO VIDEO-PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Safety Precautions Page Page Page Page Page Page 1.1 About This Manual 1. Introduction 1.2 Using This Manual DANGER! 1.3 Description, Features and Benefits Page Runco SC-1 Owners Operating Manual 5 2.1 SC-1 at a Glance Figure 2-1 shows the key SC-1 components. The paragraphs that follow describe them. Figure 2-1. SC-1 Top/Rear/Front/Side View (with Built-In Power Supply/Ballast) 2. Controls and Functions Page Controls and Functions Runco SC-1 Owners Operating Manual 7 2.2 SC-1 Input Panel Figure 2-2 shows the SC-1 rear input panel. Figure 2-2. SC-1 Input Panel Page 2.3 SC-1 Control Panel Page 2.4 DHD Controller Front Panel 2.5 DHD Controller Rear Panel Page 2.6 DHD Controller Remote Control Page Page 3. Installation 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Screen x Lens Throw Ratio = Approximate Throw Distance Table 3-3. SC-1 Lens Options and Throw Ratios Page 20% Offset 3.4 Installing the Projection Lens, Lamp and Cooling Page Page Page Page Page Page 3.6 Mounting the SC-1 3.7 Connections to the SC-1 and DHD Controller Figure 3-13. Connecting the SC-1 to the DHD Controller RGB-HV OUT DHD Controller Runco SC-1 Owners Operating Manual 33 IR Page Runco SC-1 Owners Operating Manual 35 Digital (DTV) RGB or Component Video Connections: See Figure 3-15. Red/Pr Green/Y Blue/Pb Horiz Vert Figure 3-15. Digital (DTV) RGB or Component Video Connections DTV or Progressive Component (YPbPr) Source 36 Runco SC-1 Owners Operating Manual Analog (Computer) RGB Connections: See Figure 3-16. Red Green Blue Horiz Vert Personal Computer Figure 3-16. Analog RGB Connections Runco SC-1 Owners Operating Manual 37 Composite/S-Video/Component Video Connections: See Figure 3-17. Pb Pr Y Figure 3-17. Composite, S-Video and Component Video Connections DVD Player, VCR, Satellite Receiver, Laser Disc etc. 38 Runco SC-1 Owners Operating Manual to Automation/ Control System or PC 2 Transmit Data 3 Receive Data 5 Ground (none of the other pins are used) HD1 HD2 ! LEGEND FROM BALLAST (male) (female) Page Page 3.8 Turning on the Power Component SD NTSC 480i Anamorphic SC-1 DVI 3.9 Maximizing Light Output Page Page 3.13 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Wrong Position Correct Position 3.14 Calibrating Projector Inputs Figure 3-28. TheaterMaster Remote Control for SC-1 + - MAIN Page 01 0,1 p5W 48.73k+ 60.01+ 02 0,2 pDig DVI out fm DHD 03 0,1 i5W 33.72k- 60.00- Page Page Page Page Page Page Page 3.15 Working With the Lamp Page Page 4. Operation Operation Figure 4-1. DHD Controller OSD Menu Structure for SC-1 Input Source Calibration ISF Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page -+ Page 5.1 Safety Guidelines 5. Maintenance and Troubleshooting 5.2 Maintaining Proper Cooling 5.3 Maintenance and Cleaning Page 5.4 Lamp and Filter Replacement Page Page Page 5.5 Lens Replacement 5.6 Troubleshooting Tips Table 5-1. Troubleshooting Chart Table 5-1. Troubleshooting Chart (continued) Table 5-2. SC-1 Error Codes Page Table 5-2. SC-1 Error Codes (continued) 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax 6. Serial Communications Table 6-1. Serial Commands Page Page Page Page 7.1 SC-1 Specifications Table 7-1 lists the SC-1 specifications. 7. Specifications Table 7-1. SC-1 Specifications Table 7-1. SC-1 Specifications (continued) 7.2 DHD Controller Specifications Table 7-2 lists the DHD Controller specifications. Table 7-2. DHD Controller Specifications Specifications 106 Runco SC-1 Owners Operating Manual 7.3 SC-1 Dimensions Figure 7-1 and Figure 7-2 show the SC-1 dimensions (all dimensions are in inches). Figure 7-1. SC-1 Dimensions (with Built-In Power Supply/Lamp Ballast) Specifications Figure 7-2. SC-1 Dimensions (without Built-In Power Supply/Lamp Ballast) Runco SC-1 Owners Operating Manual 107