Sagem 1500, 1500WG - page 92

4 - Configuring the SAGEM F@st™ 1500 ADSL router

SAGEM F@st™ 1500 Reference Manual - 288053220-03

Page 4-46 Reproduction and communication prohibited without the written permission of E

E E

E

Parameter Description

General RIP Parameters

RIP mode Globally enables or disables RIP.

Auto summary If Auto summary is disabled, then RIP packets will include sub-

network information from all subnetworks connected to the

router. If enabled, this sub-network information will be

summarized to one piece of information covering all

subnetworks.

Table of current Interface RIP parameter

Interface The WAN interface to be configured.

Operation Mode • Disable: RIP disabled on this interface.

• Enable: RIP enabled on this interface.

• Silent: Listens for route broadcasts and updates its route table.

It does not participate in sending route broadcasts.

Version Sets the RIP (Routing Information Protocol) version to use on

this interface.

Poison Reverse A method for preventing loops that would cause endless

retransmission of data traffic.

Authentication

Required

• None: No authentication.

• Password: A password authentication key is included in the

packet. If this does not match what is expected, the packet will

be discarded. This method provides very little security as it is

possible to learn the authentication key by watching RIP

packets.

• MD5: An algorithm that is used to verify data integrity through

the creation of a 128-bit message digest from data input (which

may

be a message of any length) that is claimed to be as unique to

that specific data as a fingerprint is to a specific individual.

Authentication

Code

Password or MD5 Authentication key.

RIP sends routing-update messages at regular intervals a nd when the network topologychanges. When a router receives a routing update that includes changes to an entry, it updatesits routing table to reflect the new route. RIP routers maintain only the best route to adestination. After updating its routing table, the router immediately be gins transmitting routingupdates to inform other network routers of the change.

Contents

Main Warning ! Contents 1. Introduction 1-1 2. Description and Physical installation 2-1 3. Configuring Client Computer 3-1 4. Configuring the SAGEM F@st 1500 ADSL router 4-1 A. Appendix A - Troubleshooting A-1 B. Appendix B - Safety warnings B-1 C. Appendix C - CABLES C-1 D. Appendix D - Technical specifications D-1 E. Appendix E - Default configuration E-1 List of figures 1. Introduction 1.1 About the SAGEM F@stTM 1500WG ADSL Router 1.2 Features and Benefits 1.3 Applications Wireless and Wired LAN Internet Access Shared IP Address Virtual Server DMZ Host Support Security Virtual Private Network (VPN) 1.4 Composition of the supply 1.5 Prerequisites Page 2. Description and Physical installation 2.1 Hardware Description 2.1.1 Front panel 2.1.2 Rear panel 2.2 Physical Installation 2.2.1 Installation instructions Environment Power supply source Maintenance Page 2.3 Settings and Connecting 2.3.1 ISP settings 2.3.2 Install the SAGEM F@stTM 1500 ADSL Router 2.3.3 Connect the ADSL Line 2.3.4 Phone Line Configuration Page 2.3.5 Attach to Your Network Using Ethernet Cabling 2.3.6 Connect the Power Adapter 2.4 Powering up the SAGEM F@st 1500 ADSL router Page Page PC Mac 3.1 TCP/IP Configuration 3.2 Configuring your Windows computer 3.2.1 On Windows 98 / Me Page Page Page Page Page Page TCP/IP Configuration Setting Page 3.2.3 On Windows 2000 Page Page Page 3.2.4 On Windows XP Page Obtain IP Settings from Sagem F@st1500 ADSL Router Page 3.3 Configuring your Mac computer Page Page Page Navigating the Management Interface Setup Wizard: Advanced Setup: Making Configuration Changes Page 4 - Configuring the SAGEM F@st 1500 ADSL router 4.1 STATUS Page 4.2 "SETUP WIZARD" menu 4.2.1 PPP Setting 4.2.2 Channel and SSID 4.2.3 WEP 4.2.4 Access Control 4.3 SYSTEM 4.3.1 Time Settings 4.3.2 Password Settings 4.3.3 Configuration tools 4.3.4 Firmware Upgrade 4.3.5 Reset 4.4 "WAN" menu E Page 4-15 4.4.1 ATM PVC Enter ATM (Asynchronous Transf er Mode) function parameters here. E The following parameters only appear in "Routed" mode that you can select in the "Protocol" field: Page 4.5 LAN 4.5.1 DNS 4.6 Wireless 4.6.1 Channel and SSID 4.6.2 Access Control Page 4.6.4 WEP 4.6.5 WPA Page Page 4.7 NAT 4.7.1 Address Mapping 4.7.2 Virtual Server 4.7.3 Special Application Page 4.8 Firewall 4.8.1 Access Control Page 4.8.2 MAC Filter 4.8.3 URL Blocking 4.8.4 Schedule Rule 4.8.5 Intrusion Detection 1) Intrusion Detection Feature 2) Stateful Packet Inspection Page 3) When hackers attempt to enter your network, we can alert you by e-mail 4) Connection Policy 5) DoS Criteria and Port Scan Criteria 4.8.6 DMZ 4.9 Route 4.9.1 Static Route Page Page 4.9.3 Routing Table 4.10 QoS Page 4.10.1 Traffic Mapping Page 4.10.2 Traffic statistics 4.11 Advanced 4.11.1 ADSL ADSL Status Information Page The following items are included on this inform ation page: 4.11.2 Remote Management 4.11.3 SNMP SNMP Setting SNMP Trap 4.11.4 UPnP 4.12 Finding the MAC address of a Network Card Page Page Appendix A - Troubleshooting Page Page Page Appendix B - Safety warnings B.1 Safety warnings B.1.1 Safety levels on the mains adapter unit B.1.2 Safety levels on the SAGEM F@st 1500 unit Appendix B - Safety warnings B.2 CE declaration of conformity Safety EMC Radio (specific to SAGEM F@st 1500WG) Page Page C.1 Ethernet cable C.1.1 Specifications C.1.2 Wiring Conventions C.1.3 RJ-45 Port Connection C.1.4 Pin Assignments General Straight-Through Wiring Crossover Wiring Page C.2.2 Wiring Conventions Page D. Appendix D - Technical specifications D.1 Mechanical Characteristics - Displays D.2 Electrical Characteristics ADSL Features Input Power D.3 Soft Component Features ATM Features Management Features Security Features LAN Features D.4 Radio Features RF Output Power Modulation Rate-Output Power (dBm) Modulation Rate-Output Power (dBm) Sensitivity Modulation Rate-Receiver 2.412 ~ 2.484 HGz Sensitivity (dBm) Modulation Rate-Receiver Sensitivity Typical (dBm) D.5 Environmental characteristics Internet Standards Page Page Appendix E - Default configuration E.1 Default user name and password Password Empty E.2 Default configuration on the local area network side E.3 Default configuration on the wide area network side Appendix E - Default configuration