Clearing Paper Jams, Paper Exit Area | Samsung ML-2015/XEV specification

Alignment and Adjustments

4.7.1 Clearing Paper Jams

Occasionally, paper can be jammed during a print job. Some of causes include:

•The tray is overfilled.

•The front cover has been opened during a print job.

•Paper that does not meet paper specifications has been used.

•Paper that is outside of the supported size range has been

If a paper jam occurs, the On Line/Error LED on the control panel lights red. Find and remove the jammed paper. If it is invisible, look inside the printer.

4.7.2 In the Paper Exit Area

1. If the paper jams as it exits to the output tray and a long portion of the paper is visible, pull the paper straight out.

When you pull the jammed paper, if there is resistance and the paper does not move immediately, stop pulling. Continue with the next step.

2. Open the top cover and the inner cover.

Heat roller

4-12Service Manual

Samsung Electronics

Image 57

Samsung ML-2015/XEV manual Clearing Paper Jams, Paper Exit Area

Contents

Laser Printer Version no .00 Code JC-0141I Contents Troubleshooting Disassembly and ReassemblyExploded Views & Parts List Block diagram Circuit Description Reference Information Safety Warning Precautions Safety Caution Noxious Material PrecautionElectric Shock or fire Precaution Assembly/Disassembly precaution Handling Precautions ESD Precautions Specifications General SpecificationsProduct Overview Controller Product Specifications Descriptions Electrical Specification Environmental RangeToner Cartridge Input Paper Size Paper Handling Specifications ML-1610 Series ML-2010 Series Remark Model Comparison Table System Outline System Overview Hvps Smps Transfer Ass’y FeedingDriver Ass’y Fuser System Overview LSU Laser Scanner Unit Cleaning Blade 1 H/W Overview H/W Structure and Descriptions Flash Memory 12.0MHz Main Board Sdram AsicSPGPm Specification Interrupt Controller Intc TimerUSB interface Serial port interface Uart Jupiter4E Internal Block Diagram Paper Feeding/Width Sensor Controller Pin Signal Smps board Switching Module Power Supply CH1 CH2 Smps Specification Transfer High Voltage THV+ Hvps board High Voltage Power SupplyCharge Voltage MHV Developing Voltage DEV Supply Fuser AC Power Control S/W Structure and Descriptions IntroductionEngine Control F/W Overview Fan Unit Motors Solenold Clutch 3 F/W Architecture of Engine Control Firmware Engine Interface Module DesignEngine Sensing & Unit Control Module Design Start LED Behaviors Error LED Operation Initial Product Installation Accessory ListInstalling the Toner Cartridge System Overview Samsung Electronics You can load approximately 150 sheets of paper in the tray Loading Paper Connecting a Printer Cable Printing a Demo Turning the Printer on If you are printing from Windows Installing Printer SoftwareIf you are printing in Linux System Requirements Sample Pattern Alignment and Adjustments Control Panel OP Panel On Line/Error and Toner Save LEDs Cancel button LED Status Error Message Consumables and Replacement Parts Roller Defective image Typical defect Periodic Defective Image DCU Setup How to use DCU Normal Code Code Self Diagnostic Mode 13 THV+ TRIGGER. ALL HV Functi on Enter Up/ Down Stop Remar k Self Test Button Paper Path Paper Exit Area Clearing Paper Jams Samsung Electronics Around the Toner Cartridge Paper Feed Area Samsung Electronics Solving Print Quality Problems Print Quality ChecklistTips for Avoiding Paper Jams Disassembly and Reassembly Front Cover Disassembly and Reassembly MP Tray Smps Cover Cassette Tray Main Cover Top Cover Hvps RX Drive Thermister Thermo Cap For removing only SMPS, perform the follows in order Engine Shield Including Main PBA and Smps 11 LSU Paper Path Frame PickUp Roller Checking Symptoms Troubleshooting Basic Check List Check the Installation Environment Check Power partInitial Inspection Check paper type Bad discharge Check and Cause SolutionWrong Print Position 2 JAM 4 JAM 3 JAM Multi-Feeding Paper rolled in the Toner Cartridge OPC Drum All LEDs blinking Fuser Error All LEDs blinking Scan ErrorMalfunction Not function of the gear of the fuser due to melting away Paper EmptyPaper Empty without indication Cover Open No lamp on when the cover is open Defective motor operation No Power Vertical Line Getting Curved Printer is not working Bad Software Environment Utilities program Abnormal Printing How to delete the data in the spool manager Spool Error Bad image Vertical Black Line and BandVertical White Line Black/White Spot Horizontal Black Band Dark Image or a Black Light Image Background Uneven Density Ghost Description Digital Printer Stains on the Face Blank Page Print out Stains on Back Exploded Views and Parts List ML-2010/XEV Main Assembly Assembly Fuser Unit Paper Path Unit MP Tray Assembly Basic Parts List ML-2010/XEV Paper Path Assembly MP Tray Assembly FELT-FRAME Noise LML-2010,POLYESTER RAY SNA IC ASIC-JUPITER4ES4FD004X,ML-1520,160P MEC-BUSHING AGI LSF-5100,SEC,POM+SANTOP SNA JUPITER4e ML-201520ppm GDI P1284 H/W Block Diagram +5V+24V Diagram Schematic Diagrams Main Board2/5 Main Board3/5 Main Board4/5 Main Board5/5 Connector Circuit Diagram Smps Circuit Diagram Hvps Circuit Diagram1/3 Hvps Circuit Diagram2/3 Hvps Circuit Diagram3/3 Troubleshooting Tool Abbreviations Explanation Acronyms and Abbreviations1 SPL Acronyms and Abbreviations2 Selecting printer locations A4 ISO 19752 Standard Patterns Sample Tests Patterns Heater Control 12.1 Engine Controller Circuit Description PWM Controller LSU Controller Motor Driver APB Bridge PVC Lsuc Name Direction Description ADC Controller