Input Mode PC/DVI | Samsung PS42P2SB, PS50P2HB specs

Input Mode (PC/DVI)

ENG

Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported:

	Standard			Dot x Line		Vertical	Horizontal	Vertical	Horizontal
	Standard			Dot x Line		frequency (Hz)	frequency (kHz)	polarity	polarity
						frequency (Hz)	frequency (kHz)	polarity	polarity

	VGA			640 x 480		85.0	43.3	N	N
						75.0	37.5	N	N
						72.8	37.9	N	N
						59.9	31.5	N	N
				720 x 400		70.1	31.5	P	N
	SVGA			800 x 600		85.1	53.7	P	P
						75.0	46.9	P	P
						72.2	48.1	P	P
						60.3	37.9	P	P
						56.3	35.2	P	P
	XGA			1024 x 768		85.0	68.7	P	P
						75.0	60.0	P	P
						70.1	56.5	N	N
						60.0	48.3	N	N
	WXGA			848 x 480		85	42.9	P	N
						75	37.5	P	N
						72	36.1	P	N
						70	35.0	P	N
						60	29.8	P	N

(N: Negative / P: Positive)

◆The interlace mode is not supported.

◆The PDP might operate abnormally if a non-standard video format is selected.

◆The 4:3 mode does not work with input signals from “720 x 400”.

◆The DVI mode does not support “1024 x 768” (85Hz).

Notes

◆The text quality of PC screen is optimum in the VGA mode (640 x 480), the full size displayed PC mode is optimum in the SVGA mode (800 x 600).

◆When this PDP is used as a PC display, 24-bit color is supported (over 16 million colors).

◆Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows). Check your PC instruction book for information about connecting your PC to a PDP.

◆If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz (horizontal).

In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the Source button to enter the Video mode. Also, make sure that the PC is connected.

◆When connecting a notebook PC to the PDP, make sure that the PC screen is displayed through only the PDP monitor (Otherwise, random signals might appear).

◆When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable connections.

53

Image 53

Samsung PS42P2SB, PS50P2HB manual Input Mode PC/DVI, Standard Dot x Line Vertical Horizontal

Contents

Plasma Display with Media Station User Instructions Safety Instructions Checking Parts Contents Contents Plug the mains lead into an appropriate For further details, refer to Switching On and Off onViewing the Plasma Display For further details about connection, refer to pages 48~51 Viewing the Media Station Power Remote Control Buttons Installing the Display on the Wall Attachment Panel Inserting the Batteries in the Remote Control Degrees of tilt No tilt Been set to 5 degrees Been set to 15 degrees Been tilted Bolt Insulation rubber Remove four large screws from the rear side of the display Separating the Display from the Wall Attachment Panel Connecting Speakers Connecting to an Aerial or Cable Television Network Switching On and Off Menu Becoming Familiar with the Remote ControlButton Viewing Function Menu Function Setting up your Remote Control To start the store, press the joystick button Plug and Play Choosing Your Language Lock the channels see Storing Channels Automatically Sorting the Stored Channels D/K I M Storing Channels ManuallyAuto PAL Secam NTSC4.43 NTSC3.58 Channel mode LNA Editing the Channels Fine Tuning Channel Reception To adjust the Contrast, Brightness, Sharpness, Colour, or Adjusting the Picture SettingsChanging the Picture Standard Custom Dynamic Standard Movie Custom High Middle Low Standard Full Normal Changing the Picture SizeFreezing the Current Picture Custom Colour l Colour 2 Colour Adjusting the Picture Settings PC or DVI Mode Preset to the PC mode by using the Source button Setting the Picture PC Mode Custom Standard Music Movie Speech Adjusting the Sound SettingsChanging the Sound Standard Adjusting the Volume Automatically Selecting the Sound Mode Normal Phantom Wide Setting the Dolby SurroundOff Virtual Pro Logic Virtual OffNormal Phantom Adjusting the Dolby Pro Logic Preferences Volume, Bass, Treble, Balance Adjusting the Headphone Preferences Adjust the each option Up or down Setting the Current TimeHearing the Melody Sound Move the joystick Switching On and Off Automatically Press the Sleep button on the remote control Setting the Sleep Timer TV AV 1 AV 2 AV 3 AV 4 AV Viewing the Picture in Picture PIP Large Small Double 1 Double Listening to the Sound of the Sub Picture Front panel Viewing Pictures From External Sources Contents Teletext Feature Displaying the Teletext Information To display Press Selecting Display OptionsSecondary page by entering its number Time/Subcode Selecting a Teletext Input Connecting to the S-Video Input Connecting to the DVD Input Connecting to the DVI Input Connecting to the Audio Output Preset Signals Connecting to the PC InputFrequency Horizontal frequency Resolution Source Video 1024 x 768 pixels Setting up Your PC Software Windows only Standard Dot x Line Vertical Horizontal Input Mode PC/DVI Pin Pin ConfigurationsPinSignal Care and Maintenance Troubleshooting After Sales Service