Changing the Picture Standard | Samsung PS50P2HB, PS42P2SB instruction

Changing the Picture Standard

ENG

		Picture
Mode		Custom
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone		Normal
Move	Select	Menu

PC Mode
		Picture
Mode		Middle
Contrast
Brightness
Sharpness
Colour Tone
Move	Select	Menu

You can select the picture mode which best corresponds to your viewing requirements.

1Press the MENU button.

Result: The Picture menu is displayed.

2Press the joystick button to enter the picture menu.

Result: The Mode is selected.

3To select the picture effect which best corresponds to your viewing requirements, move the joystick left or right.

Result: The following modes are available depending on the input source.

◆Custom - Dynamic - Standard - Movie

◆Custom - High - Middle - Low

(PC or DVI Mode)

➣You can select these options by simply pressing the P.STD (Picture Standard) button on the remote control.

Adjusting the Picture Settings

		Picture
Mode		Custom
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone		Normal
Move	Adjust	Menu
		Picture
Mode		Custom
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone		Normal

Move

Select

Menu

Your PDP has several settings which allow you to control picture quality.

1Press the MENU button.

Result: The Picture menu is displayed.

2Press the joystick button to enter the picture menu.

3Select a option to be adjusted by moving the joystick up or down.

4To adjust the Contrast, Brightness, Sharpness, Colour, or

Tint (NTSC only), move the joystick left or right.

Result: The horizontal bar is displayed. Move the joystick left or right until you reach the setting.

◆In the PC mode, you can not adjust the Colour and Tint,

5To adjust the Colour Tone, move the joystick left or right.

Result: The following options are available.

Normal - Cool 1 - Cool 2 - Warm 2 - Warm 1

➣If you make any changes to these settings, the picture mode is automatically switched to the Custom.

26

Image 26

Samsung PS50P2HB, PS42P2SB Changing the Picture Standard, Adjusting the Picture Settings, Normal Cool 1 Cool 2 Warm 2 Warm

Contents

Plasma Display with Media Station Safety Instructions User Instructions Checking Parts Contents Contents Plug the mains lead into an appropriate For further details, refer to Switching On and Off onViewing the Plasma Display Viewing the Media Station For further details about connection, refer to pages 48~51 Remote Control Buttons Power Inserting the Batteries in the Remote Control Installing the Display on the Wall Attachment Panel Been set to 5 degrees Been set to 15 degrees Been tilted Degrees of tilt No tilt Remove four large screws from the rear side of the display Bolt Insulation rubber Separating the Display from the Wall Attachment Panel Connecting Speakers Connecting to an Aerial or Cable Television Network Switching On and Off Menu Becoming Familiar with the Remote ControlButton Viewing Function Menu Function Setting up your Remote Control Plug and Play To start the store, press the joystick button Choosing Your Language Storing Channels Automatically Lock the channels see Sorting the Stored Channels D/K I M Storing Channels ManuallyAuto PAL Secam NTSC4.43 NTSC3.58 Channel mode Editing the Channels LNA Fine Tuning Channel Reception Changing the Picture Standard Adjusting the Picture SettingsTo adjust the Contrast, Brightness, Sharpness, Colour, or Custom Dynamic Standard Movie Custom High Middle Low Standard Full Normal Changing the Picture SizeFreezing the Current Picture Adjusting the Picture Settings PC or DVI Mode Custom Colour l Colour 2 Colour Setting the Picture PC Mode Preset to the PC mode by using the Source button Custom Standard Music Movie Speech Adjusting the Sound SettingsChanging the Sound Standard Adjusting the Volume Automatically Selecting the Sound Mode Normal Phantom Wide Setting the Dolby SurroundOff Virtual Pro Logic Normal OffVirtual Phantom Adjusting the Dolby Pro Logic Preferences Adjusting the Headphone Preferences Volume, Bass, Treble, Balance Hearing the Melody Sound Setting the Current TimeAdjust the each option Up or down Move the joystick Switching On and Off Automatically Setting the Sleep Timer Press the Sleep button on the remote control Viewing the Picture in Picture PIP TV AV 1 AV 2 AV 3 AV 4 AV Large Small Double 1 Double Listening to the Sound of the Sub Picture Viewing Pictures From External Sources Front panel Teletext Feature Contents Displaying the Teletext Information Secondary page by entering its number Selecting Display OptionsTo display Press Time/Subcode Selecting a Teletext Input Connecting to the DVD Input Connecting to the S-Video Input Connecting to the Audio Output Connecting to the DVI Input Frequency Horizontal frequency Resolution Connecting to the PC InputPreset Signals Source Video Setting up Your PC Software Windows only 1024 x 768 pixels Input Mode PC/DVI Standard Dot x Line Vertical Horizontal Pin Pin ConfigurationsPinSignal Troubleshooting Care and Maintenance After Sales Service