Sanyo DVW-7100a instruction manual Hint for Timer Recording, Copying a Video Tape

H9680UD_EN/SP.qx3 04.8.10 4:26 PM Page 13

Hint for Timer Recording

•If there is a power failure or the DVD+VCR has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.

•If a tape is not in the DVD+VCR or does not have the record tab, the TIMER REC light flashes and timer recording cannot be performed. Please insert a recordable tape.

•If a tape ends during timer recording, the VCR will stop, eject the tape, and switch to the DVD mode automati- cally as the TIMER REC light flashes. (If the DVD power is off, the VCR will become STANDBY status.)

•When all timer recordings are finished, the TIMER REC light will flash.

•When timer recordings are set, the TIMER REC light will appear. To use the VCR as usual until the time for the recording, press the SUBTITLE/T-SET button so that the TIMER REC light disappears. Press the VCR/TV button to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual.

If you want to use the DVD player during a VCR timer recording or while the TIMER REC light is on or flashes.

•You can use the DVD player while the TIMER REC light is on or flashes, or during a timer recording. Press the POWER button to turn on the DVD. Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don’t have to set the TIMER off to use the DVD only.

Copying a Video Tape

Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.

(Back of TV)

(Back of another source) (Back of Recording DVD+VCR*)

or	DVD/VCR VCR		1		DVD		DVD/VCR VCR			2
	AUDIO OUT	AUDIO IN
	AUDIO OUT			DIGITAL	AUDIOS-VIDEO	COMPONENT	AUDIO OUT
						VIDEO OUT		AUDIO IN
	L	L		AUDIO OUT	L	Y	L		ANT-IN	Connect
					OUTOUT
	R	R	Connect			CB	R	R

VIDEO OUT	VIDEO IN	ANT-OUT	COAXIAL
VIDEO OUT				VIDEO OUT VIDEO IN	ANT-OUT
			R
				CR

	RF cable
Audio/Video cables	(supplied)
	*Front input jacks are also available
(not supplied)

Hint

•For best results during dubbing, use the front panel controls whenever possible. The remote control might affect another source’s operation.

•Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended.

•You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs.

•“L1” or “L2” is found before the lowest memorized channel. (Example: CH02)

•“L2” input jacks are on the front of this DVD+VCR.

1)Insert a pre-recorded tape into the playing VCR.

2)Insert a tape with its record tab into the recording DVD+VCR.

3)Press the SPEED button on the remote control of the recording DVD+VCR to select the desired recording speed (SP/SLP).

4)Select the "L1" or "L2" position on the recording DVD+VCR.

•To use the input jacks on the back of this unit, select "L1" position by pressing [0], [0], [1] on the remote control or the CHANNEL buttons.

•To use the input jacks on the front of this unit, select "L2" position by pressing [0], [0], [2] on the remote control or the CHANNEL buttons.

5)Press the REC/OTR button on the recording DVD+VCR.

6)Begin playback of the tape in another source.

7)To stop recording, press the STOP/EJECT button on the recording DVD+VCR, then stop playback of the tape in another source.

VCR Functions

Need help? Call 1-800-813-3435

– 13 – EN