Manuals / Sanyo / Computer Equipment / Projector

Sanyo PDG-DXL100 owner manual Powering Off the Projector, Installation

Models: PDG-DXL100

1 63

Download 63 pages 39.07 Kb

Page 17

Image 17

Installation

Powering Off the Projector

1.Press the “ON/STAND-BY” to turn off the projector lamp, you will see a message as below on the on-screen display.

2.Press the “ON/STAND-BY” again to confirm.

3.The cooling fan continues to operate for about 60 seconds for cooling cycle and the POWER LED will flash green. When the light starts flashing orange, the projector has entered standby mode.

If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press “ON/STAND-BY” to restart the projector.

4.Disconnect the power cable from the electrical outlet and the projector.

5.Do not turn on the projector immediately following a power off procedure.

English

Page 17

Image 17

Sanyo PDG-DXL100 owner manual Powering Off the Projector, Installation

Contents

Owners Manual MODEL PDG-DXL100Multimedia Projector English Table of ContentsEnglish Table of ContentsEnglish PrecautionsUsage Notice English Usage NoticeEnglish SIDE and TOPEnglish Usage NoticeDo not English Product FeaturesIntroduction English Package OverviewIntroduction Projector Product Overview4. Ventilation outlet 7. Ventilation inlet 8. SpeakerIntroduction Connection PortsControl Panel Sends signals to the projector Remote ControlSignals indicator for sending Refer to the “Power On/Off the Prolevel of OSD for the OSD main menu IntroductionEnglish IntroductionRemote Control Operating Range Remote Control Battery InstallationTo ensure safe operation, please observe the following precautions Maximum operating rangeConnecting the Projector InstallationConnect to Computer/Notebook EnglishInstallation Connect to Video Other than the analog RGB signal ent accessoriesPowering On the Projector Powering On/Off the ProjectorPower Lens CapInstallation Powering Off the ProjectorEnglish Warning IndicatorInstallation Adjusting the Height of Projector Image Adjusting the Projected ImageTo raise/lower the image 1. Use  to fine-tune the display angle Maximun Length7mmAdjusting Projection Image Size Adjusting the Projector FocusInstallation EnglishUser Controls How to operateOn Screen Display tings. The projector will automatically detect the sourceImage Mode Image PC ModeBrightness ContrastWhite Peaking Fine SyncColor Temp GammaColor Image Video ModeImage Mode User ControlsSharpness TintUser Controls White PeakingKeystone ScreenH-position Horizontal Position V-position Vertical Position Front-Desktop The factory default setting  Rear-Desktop MountingUser Controls EnglishECO Mode SettingRS232 Mode Input SearchRemote Control Eco Standby Power 1WPower Management Closed CaptionSecurity Settings Lamp Counter ResetFactory Default User ControlsNetwork Status Setting/NetworkDHCP IP AddressInformation LanguageLanguage InformationConfiguring the Network Setting Controlling the Projector From WebUser Controls English1 IP address 2 Subnet mask 3 Default gateway click Change settings of this connectionthe Proxy Server area, cancel the 1 User name user / Password user 2 User name administratorEnglish User ControlsStep 9 The web page will display as below Step 10 Open “Control Panel” to control your projectorWhen Home page display error status, it indicates the lamp Home Pageservice center User ControlsHow to operate Control Panel page Control Panel PageUser Controls EnglishProjector Setting Network Setting PageNetwork Setting Password SettingTelnet Password Setting Security Setting PagePJLink Password Setting User ControlsEmail Setting Alert Setting PageSMTP Setting Alert ConditionWhen you use this page, the projector system will go back Login mode Logout PageUser Controls EnglishProblem No image appears on screen TroubleshootingProblem Partial, scrolling or incorrectly displayed image AppendicesEnglish Problem Image is unstable or flickeringAppendices Problem The image is stretched when displaying 169 DVD Problem Image is out of focusProblem Image is reversed Problem Lamp burns out or makes a popping soundAppendices Problem LED lighting messageEnglish TEMP Fan failed - the system fan is not working  Setting network Problem Message RemindersAppendices EnglishReplacing the lamp Lamp Replacing ProcedureAppendices EnglishIF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN Service Parts No. 610 346projection lamp, give the following information to the dealer ORDER REPLACEMENT LAMPAir Filters Cleaning Procedure Cleaning the Air FiltersRECOMMENDATION AppendicesAppendices SpecificationsEnglish English1 Signals from D-sub Computer Compatibility AnalogResolution Power Mac G41 PC digital signals with HDMI-DVI cable Computer Compatibility Digital- HDMIResolution Power Mac G4Resolution 2 AV digital signals with HDMI cableAppendices EnglishTerminal Analog RGB Mini D-sub 15 pin Configurations of TerminalsTerminal Mini DIN 8-pin AppendicesFCC notice Regulation & Safety NoticesNotice Shielded cables This appendix lists the general notices of your ProjectorNotice Canadian users Operation conditionsRemarque à l’intention des utilisateurs cana- diens Declaration of Conformity for EU countriesOperation Serial Control InterfaceAppendices EnglishFormat Functional Execution CommandAppendices EnglishCommand one character refer to the command table below Status Read CommandAppendices FormatControl Use of TelnetAppendices EnglishAppendices PJLink NoticeEnglish close returnAppendices DimensionsEnglish EnglishKF8A