Manuals / Sanyo / Computer Equipment / Projector

Sanyo PDG-DXL100 Powering On/Off the Projector, Powering On the Projector, Lens Cap, Installation

Models: PDG-DXL100

1 63

Download 63 pages 39.07 Kb

Page 16

Image 16

Installation

Powering On/Off the Projector

Powering On the Projector

1.Ensure that the power cable and signal cable are securely connected. The POWER LED will turn orange.

2.Remove the lens cap. 

3.Turn on the lamp by pressing “ON/STAND-BY” on the control panel.  The POWER LED will now flash green.

The startup screen will display in approximately 5 seconds.

When disappear startup screen, the POWER LED will turn green.

4.Turn on your source (computer, notebook, video player, etc.) The projector will detect your source automatically.

If you connect multiple sources at the same time, use the

“INPUT” on the remote control or use “COMPUTER 1”,

“COMPUTER 2”, “S-VIDEO”, “VIDEO”, “HDMI” on the remote control to switch inputs.

Note

Turn on the projector

first and then the signal

sources.

1	2
Lens Cap	Power

English

Page 16

Image 16

Sanyo PDG-DXL100 owner manual Powering On/Off the Projector, Powering On the Projector, Lens Cap, Installation, English

Contents

Multimedia Projector MODEL PDG-DXL100Owners Manual Table of Contents EnglishEnglish Table of ContentsUsage Notice PrecautionsEnglish Usage Notice EnglishEnglish SIDE and TOPDo not Usage NoticeEnglish Introduction Product FeaturesEnglish Introduction Package OverviewEnglish Product Overview Projector4. Ventilation outlet 7. Ventilation inlet 8. SpeakerControl Panel Connection PortsIntroduction Remote Control Sends signals to the projectorSignals indicator for sending Refer to the “Power On/Off the ProIntroduction level of OSD for the OSD main menuIntroduction EnglishRemote Control Battery Installation Remote Control Operating RangeTo ensure safe operation, please observe the following precautions Maximum operating rangeInstallation Connecting the ProjectorConnect to Computer/Notebook EnglishConnect to Video Installation Other than the analog RGB signal ent accessoriesPowering On/Off the Projector Powering On the ProjectorPower Lens CapPowering Off the Projector InstallationInstallation Warning IndicatorEnglish Adjusting the Projected Image Adjusting the Height of Projector ImageTo raise/lower the image 1. Use  to fine-tune the display angle Maximun Length7mmAdjusting the Projector Focus Adjusting Projection Image SizeInstallation EnglishHow to operate User ControlsOn Screen Display tings. The projector will automatically detect the sourceImage PC Mode Image ModeBrightness ContrastFine Sync White PeakingColor Temp GammaImage Video Mode ColorImage Mode User ControlsTint SharpnessUser Controls White PeakingScreen KeystoneH-position Horizontal Position V-position Vertical PositionMounting  Front-Desktop The factory default setting  Rear-DesktopUser Controls EnglishSetting ECO ModeRS232 Mode Input SearchEco Standby Power 1W Remote ControlPower Management Closed CaptionLamp Counter Reset Security SettingsFactory Default User ControlsSetting/Network Network StatusDHCP IP AddressLanguage InformationLanguage InformationControlling the Projector From Web Configuring the Network SettingUser Controls Englishclick Change settings of this connection 1 IP address 2 Subnet mask 3 Default gatewaythe Proxy Server area, cancel the 1 User name user / Password user 2 User name administratorUser Controls EnglishStep 9 The web page will display as below Step 10 Open “Control Panel” to control your projectorHome Page When Home page display error status, it indicates the lampservice center User ControlsControl Panel Page How to operate Control Panel pageUser Controls EnglishNetwork Setting Page Projector SettingNetwork Setting Password SettingSecurity Setting Page Telnet Password SettingPJLink Password Setting User ControlsAlert Setting Page Email SettingSMTP Setting Alert ConditionLogout Page When you use this page, the projector system will go back Login modeUser Controls EnglishTroubleshooting Problem No image appears on screenProblem Partial, scrolling or incorrectly displayed image AppendicesAppendices Problem Image is unstable or flickeringEnglish Problem Image is out of focus Problem The image is stretched when displaying 169 DVDProblem Image is reversed Problem Lamp burns out or makes a popping soundProblem LED lighting message AppendicesEnglish TEMPProblem Message Reminders  Fan failed - the system fan is not working  Setting networkAppendices EnglishLamp Replacing Procedure Replacing the lampAppendices EnglishService Parts No. 610 346 IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKENprojection lamp, give the following information to the dealer ORDER REPLACEMENT LAMPCleaning the Air Filters Air Filters Cleaning ProcedureRECOMMENDATION AppendicesSpecifications AppendicesEnglish EnglishComputer Compatibility Analog 1 Signals from D-subResolution Power Mac G4Computer Compatibility Digital- HDMI 1 PC digital signals with HDMI-DVI cableResolution Power Mac G42 AV digital signals with HDMI cable ResolutionAppendices EnglishConfigurations of Terminals Terminal Analog RGB Mini D-sub 15 pinTerminal Mini DIN 8-pin AppendicesRegulation & Safety Notices FCC noticeNotice Shielded cables This appendix lists the general notices of your ProjectorOperation conditions Notice Canadian usersRemarque à l’intention des utilisateurs cana- diens Declaration of Conformity for EU countriesSerial Control Interface OperationAppendices EnglishFunctional Execution Command FormatAppendices EnglishStatus Read Command Command one character refer to the command table belowAppendices FormatUse of Telnet ControlAppendices EnglishPJLink Notice AppendicesEnglish close returnDimensions AppendicesEnglish EnglishKF8A