Manuals / Brands / TV and Video / VCR / Sanyo / TV and Video / VCR

Sanyo TLS-9924P Back Panel (With the RS-485/232Cinterface board)

1 56

Download 56 pages, 498.74 Kb

RQ4Q/EX (TLS-1960P GB) Wed. May, 08/2002

LOCATIONS OF CONTROLS AND INDICATORS

Back Panel (With the RS-485/232C interface board)

ALARM(1	TRO			ES
	CON		ERI
		S
	SH	L
	OT)	IN	IN

AC IN

1A C	2 D
B

RS232C

OPEN COLLECTOR (Max. 1=500mA,

2=50mA)

(

DC12-24V IN

1

2

E

ALA

M

O

T

T

T

U

T

XT

O

O

R

SE

IN

U

U

U

T

O

TIM

RE

END

O

IN

E

T)

RN

TROL

SW

SEE MANUAL

RIN

COM

A

ON

PE

TIMER

W

C

TA

REMOTE MIC IN

E F G

A RS485 B

TERMINATE

OFF ON

Do not connect to phone line.

AUDIO		VIDEO
IN OUT	IN	OUT

	L J H F 8
M	K I G 9 7 6 5 4 3 2 1

1 VIDEO OUT (video output) 1jackDC powerTLSinput-1960P only) ( 2 VIDEO IN (video input) jackA DC12-24V“–” inputINterminal 3 AUDIO OUT (audio output) jackB Do not use

4 AUDIO IN (audio input) jackC DC12-24V“+” inputINterminal

5 MIC IN (microphone input)2jack

RS-485/232C interface board (sold

6 REMOTE (remote control input)D jack

RS-232C connector (D-sub 9-pin t

7 SW OUT (switch output) terminalE RS-485 A connector (RJ-11)

8 TIMER OUT (timer recording Foutput) terminal

RS-485 B connector (RJ-11)

9 TAPE END OUT (tape end output)G terminal TERMINATE switch

F CONTROL OUT terminal

		NOTES:
	G WARNING OUT (warning output) terminal
		œ The above illustration shows the unit
	œ Signals are output when an alarm, clog detection,
		RS-485/232C interface board is instal
	video loss, non-recording or mechanism problem
	occurs.	RS-485/232C interface board is instal
	occurs.	and switchesD throughG dotonot appear.
		and switchesD throughG dotonot appear.
	H COM (common) terminal	œ The terminal may be damaged by a torq
		. .
		Nm (5kgcm) or more and by using screwdr
	I EXT TIMER IN (external timer trigger input) terminal
		tip with a diameter of 6 mm or more.
	ALARM REST IN (alarm recording reset input)
	terminal	œ Do not connect the RS-485 A and RS-48

		connectors to a phone line.
	J SERIES IN (series recording trigger input) terminal
	K CONTROL IN terminal	œ The8,F,J andKterminals can be used to
	K CONTROL IN terminal	the input and output“SELECTINGsignals. (Ref
		the input and output“SELECTINGsignals. (Ref

L ALARM IN (alarm trigger input)INPUT ANDterminalOUTPUT TERMINALS” on page 39.)

1 SHOT IN (single image recording trigger input)
terminal		œ If usingF andKtheterminals, multiple VCRs
		operated by operating a single VCR
M AC power
	input	“SYNCHRONIZATION CONTROL” on page 41.)

œ Pay attention to the polarity of the terminal“+”: red screw,( “–” : black screw).

English

7

Contents

English Deutsch Français Español Italiano PRECAUTIONS Location Moisture Condensation Problems Power on/stand-by mode CONTENTS FEATURES ACCESSORIES LOCATIONS OF CONTROLS AND INDICATORS Front Panel Digital Display 1 Operation IndicatorsNOTES: [With the RS-485/232Cinterface board] 8 Counter memory indicator EXT TIMER IN input terminal MENU RESET button Back Panel (With the RS-485/232Cinterface board) CONNECTIONS NOTE: Power Cord Installation ON-SCREENMENU Main Menu Sub-menus Using the JOG dial and SHUTTLE ring for settings ON-SCREENMENU WARNING OUT/CONTROL SET menu ALARM/SERIES REC SET menu TAPE MANAGEMENT menu TIMER SET menu SETTING THE LANGUAGE AND CLOCK Language SettingClock setting Automatic Summer Time Adjustment SUPERIMPOSE DISPLAY Selecting the Superimpose Display Changing the Superimpose Display Position VIDEO CASSETTE TAPES Loading Handling Cassette Tapes To Protect your Recordings Unloading Correct tape thread check function Setting the Action to Take When a Cassette is Loaded TAPE MANAGEMENT Setting the Tape Management Function Tape Management Conflict Display NORMAL RECORDING Normal Recording Record Pause Concerning the Number of Times Tapes can be Rerecorded on Recording Check Clog Detection Action to Take when the Video Signal Deteriorates Setting the clog detection Setting the Mode at the End of the Tape Setting the video input signal AUTOREPEAT RECORDING Autorepeat Recording Alarm Recording Setting ALARM RECORDING Alarm Recording Reset Function Checking the Alarm Recordings Time Alarm Recording Counter Display Connections to the ALARM IN Terminal Alarm Search Alarm Scan PROGRAMME TIMER RECORDING Example 1: Example 2: Setting the Holidays Changing a Programme Timer Recording To Cancel a Programme Timer Recording To cancel all programme timer button and the buttons to set/cancel the security lock (see page 38), are disabled button is pressed the timer recording indicator“ ” will start flashing RECORDING USING AN EXTERNAL TIMER INPUT Example 3: SERIES RECORDING Series Recording Setup Operation Loop recording SINGLE IMAGE RECORDING Single Image Recording Setup NORMAL PLAYBACK Normal Playback Field Advance (Forward and Reverse) SPECIAL PLAYBACK Picture Search (Forward and Reverse) Reverse Playback Still Image Slow motion (Forward and Reverse) SHUTTLE Ring Operation DAY/TIME SEARCH Day/Time Search TAPE COUNTER SECURITY LOCK 4 Digit Security Lock Quick Method Security Lock CLOCK ADJUSTMENT Connection SELECTING INPUT AND OUTPUT TERMINALS SETTING THE CASSETTE EJECT MODE Cassette Eject Setup SYNCHRONIZATION CONTROL Operator Mode Setting the Cassette Eject Mode Administrator/Installer Mode SETTING FOR RS-485OR RS-232CUSE Settings when using RS-485 Setting the Address and Data Transfer Speed CHECKING POWER FAILURE, FAILURE DUE TO CONDENSATION AND USAGE DURATION the date and time of the most recent failure and recovery are displayed OUTPUT TERMINALS TAPE END OUT TerminalCOM Terminal TIMER OUT Terminal SW OUT Terminal WARNING OUT Terminal REMOTE Jack Remote control setting HEAD SWITCHING FUNCTION MAINTENANCE Daily Inspection Inspection Procedure Periodic Inspection Cabinet Cleaning Maintaining and Checking The Mechanism TROUBLESHOOTING GUIDE After a Power Failure System Down SPECIFICATIONS SPECIFICATIONS Other Specifications Operating temperature range Connectors (When the “TERMINAL SET” is set to “SET2”)