|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Errors that are impossible to recover |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Error |
| Description |
| ERROR LED blinking pattern | Recovery | ||||||||||
| After | R/W | checking, | the |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |||||
| printer | does not | work |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||
R/W error in memory | correctly. |
|
|
|
|
|
|
| 200ms | Recovers | automatically | ||||
Writing to, | reading | out, | or |
|
|
|
| when the | rear cover is | ||||||
or gate array |
|
|
|
|
|
|
|
| |||||||
erasing the NV memory for |
|
|
|
|
|
|
|
| closed. |
| |||||
|
|
|
|
|
|
|
|
|
| ||||||
| image | scanning | results |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||
| does not work correctly. |
|
|
|
|
|
|
|
|
|
|
| |||
High voltage error | The power supply voltage |
|
|
|
|
|
|
|
| Impossible to recover. | |||||
is extremely high. |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Low voltage error | The power supply voltage |
|
|
|
|
|
|
|
| Impossible to recover. | |||||
is extremely low. |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| The CPU | executes | an |
|
|
|
|
|
|
|
|
|
| ||
CPU execution error | incorrect address | or | I/F |
|
|
|
|
|
|
|
| Impossible to recover. | |||
| board is not connected. |
|
|
|
|
|
|
|
|
|
|
| |||
Print head temperature | There is an abnormality is |
|
|
|
|
|
|
|
| Impossible to recover. | |||||
detection circuit error. | the print head temperature. |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||||||
NOTES
If you see this light blinking, turn off the printer for a few seconds and then turn it back on. If the light is still blinking, call your supervisor or a service person.
11-2 The printer does not start printing
•Are any of the operation panel lights on, If no operation panel lights are on, check the following:
-Make sure that the printer is turned on.
-Make sure that the power supply cable is correctly plugged into the printer and to the power outlet.
•If any of the lights are on, please check the following:
-If the POWER LED is blinking, the printer is not ready yet.
Wait until the light quits blinking and the printer is ready to use.
-If the ERROR LED is on (but not blinking), the printer is off line. Check to see that the covers are closed and check the paper state. See Chapter 5 for instructions on installing or replacing the paper roll.
-If the ERROR LED is blinking, there is an error. In this case, turn off the printer for a few seconds and then turn it back on. If the light is still blinking, call your supervisor or service person.
-If the PAPER OUT LED is on, check the paper roll in the printer. See Chapter 5 for instruction on installing the paper roll.
Rev. 1.01 | - 38 - |
